Yanmar SA Series Скачать руководство пользователя | Manualshive

Страница: 127 / 170

background image

14. PERIODIC SERVICE

SA221/324/424 Operation Manual

■

Check and Drain the Fuel/Water
Separator

For details, see "Check the Fuel/Water Separator" on
page 14-16.

■

Change the Engine Oil

For the maintenance work, see “Change the Engine
Oil and Replace Engine Oil Filter” on page 14-22.

■

Replace the Engine Oil Filter

For the maintenance work, see “Change the Engine
Oil and Replace Engine Oil Filter” on page 14-22.

■

Change the Transmission Hydraulic Oil

For the maintenance work, see “Change the
Transmission Hydraulic Oil, Replace the
Transmission Hydraulic Oil Filter and HST Hydraulic
Oil Filter” on page 14-24.

■

Replace the Transmission Hydraulic
Oil Filter and HST Hydraulic Oil Filter

For the maintenance work, see “Change the
Transmission Hydraulic Oil, Replace the
Transmission Hydraulic Oil Filter and HST Hydraulic
Oil Filter” on page 14-24.

■

Check the Front Axle Gear Oil Level

1. Park the tractor safely and securely.

• For details, see "7. Safe Practices for Parking the

Tractor" on page 1-7.

2. Shut off the engine.
3. Chock all the tires safely and securely.
4. Allow the engine to cool down for several

minutes.

5. Make the front axle gear oil settle for at least 1

hour.

(A) Oil cap

6. Loosen and remove the dipstick located on the

right side of the front axle.

7. Use a clean rag to wipe the front axle gear oil

from the dipstick.

8. Insert the dipstick into the hole without tightening.
9. Remove the dipstick again.
10.Check the front axle gear oil level on the dipstick.
11.The front axle gear oil level must be between the

upper and lower marks on the dipstick.

(A) Dipstick

(a) Upper mark
(b) Lower mark

4. First 50 Hours

5. Every 50 Hours

IMPORTANT

●

Before checking the front axle gear oil level, allow
the front axle gear oil to settle for 1 hour until the
current front axle gear oil level can be accurately
read on the dipstick. Recheck the front axle gear
oil level after operating the tractor for several
hours.

NOTE

●

Clean the area around the oil cap/dipstick before
removing the oil cap/dipstick.

IMPORTANT

●

When the front axle gear oil level is low:
• add SAE 80W-90 gear oil through the fill opening

until the front axle gear oil level is appropriate

(A)

Upper

Lower

(A)

SA221_324_424_OperatorsManual.book 15 ページ２０１８年６月４日　月曜日　午後５時１９分

«
...
125
126
127
128
129
...
»

Содержание SA Series











































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SA Series

Бренд: Taylor-Dunn Страницы: 60

Бренд: Rankin Страницы: 37

Бренд: Valtra Страницы: 1361

Бренд: GOLDONI Страницы: 43

Jinma 200 Series

Бренд: Yancheng Tractor Factory Страницы: 52

Luchs HYDRO LHR-2

Бренд: Koeppl Страницы: 48

Бренд: Sanderson Страницы: 17

Proxima Plus 100

Бренд: Zetor Страницы: 34

Бренд: Zetor Страницы: 37

Бренд: third coast equipment Страницы: 12

Бренд: Hitech Страницы: 24

Бренд: Case IH Страницы: 24

Бренд: Valtra Страницы: 370

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды