Yanmar SA Series Скачать руководство пользователя

Страница: 136 / 170

14. PERIODIC SERVICE

14-24

SA221/324/424 Operation Manual

■

Check the Air Intake Hoses and Hose
Clamps

1. Park the tractor safely and securely.

• For details, see "7. Safe Practices for Parking the

Tractor" on page 1-7.

2. Shut off the engine.
3. Chock all the tires safely and securely.
4. Allow the engine to cool down for several

minutes.

5. Raise the hood to access the air intake hoses and

the hose clamps.

6. Make sure that the air intake hoses and the hose

clamps are in good condition.

7. Check the hose clamps for looseness.
8. Lower the hood.

(A) Air intake hose
(B) Hose clamps

■

Transmission Hydraulic Oil

Transmission

■

Change the Transmission Hydraulic
Oil, Replace the Transmission
Hydraulic Oil Filter and HST Hydraulic
Oil Filter

NOTE

●

The illustration of the tractor shown does not
have hood.

●

Above illustration shows SA324/424.

(A)

(B)

(A)

8. Every 300 Hours

IMPORTANT

●

Always use a Hydraulic/Transmission Fluid for the
transmission hydraulic oil.

Capacity

Lubricant

Approximately

4.1 US gal (15.5 L) Hydraulic/Transmission Fluid

●

Touching any hot surfaces can burn the skin.

●

If the engine has been running for some time,
the engine components, including all internal
fluids are hot:
• always allow the engine to cool down before

performing maintenance or working near the
engine and engine parts

IMPORTANT

●

More frequent maintenance can be required
under severe or abnormal conditions.

●

Always keep the transmission hydraulic oil filler
cap in place.

●

Remove the transmission hydraulic oil filler cap
only as necessary:
• the preceding practice prevents the

transmission hydraulic oil from becoming
contaminated

• a contaminated transmission hydraulic oil can

cause damage to or failure of the transmission

●

Avoid operating the tractor immediately after the
transmission hydraulic oil is changed.

●

After the transmission hydraulic oil is changed,
run the engine at medium speed for a few
minutes, to prevent damage to the transmission.

! WARNING

SA221_324_424_OperatorsManual.book 24 ページ２０１８年６月４日　月曜日　午後５時１９分

Содержание SA Series











































































































































































Результаты поиска

Содержание SA Series

Отзывы:

Похожие инструкции для SA Series

Бренды по названию

Популярные бренды

Yanmar SA Series, Руководство по эксплуатации

Результаты поиска

Содержание SA Series

Отзывы:

Похожие инструкции для SA Series

Бренды по названию

Популярные бренды