background image

(5) FASTENER TORQUE

• Torquing Fasteners

Always  follow  the  torque  values  and  procedures  as  designated  in  the
service  manual.  Incorrect  values,  procedures  and  or  tools  may  cause
damage to the engine and or personal injury.

(6) Electrical

• Short Circuits

Always disconnect the (-) Negative battery cable before working on the
electrical  system. An  accidental  "short circuit"   may  cause  damage, fire
and  or  personal  injury.    Remember  to  connect  the  (-)  Negative  battery
cable (back onto the battery) LAST

• Charging Batteries

Charging wet celled batteries produces hydrogen gas. Hydrogen gas is
extremely  explosive.  Keep  sparks,  open  flame  and  any  other  form  of
ignition away. Explosion may occur causing severe personal injury.

• Battery Electrolyte

Batteries  contain  sulfuric  acid.  Do  NOT  allow  it  to  come  in  contact  with
clothing, skin and or eyes, severe burns will result.

(7) WASTE MANAGEMENT

Observe  the  following  instructions  with  regard  to  hazardous  waste
disposal. Negligence of these will have a serious impact on environmental
pollution  concerns.
1) Waste  fluids  such  as  lube  oil,  fuel  and  coolant  shall  be  carefully  put

into separate sealed containers and disposed of properly.

2) Do  NOT  dispose  of  waste  materials  irresponsibly  by  dumping  them

into the sewer, overland or into natural waterways.

3) Waste materials such as oil, fuel, coolant, solvents, filter elements and

batteries, must be disposed of properly according to local ordinances.
Consult the local authorities or reclamation facility.

Содержание 6LY3-ETP





















Отзывы: