Yanmar 3TNV82A Скачать руководство пользователя страница 114

Страница: 114 / 234

FAILURE DIAGNOSIS

1-112

TNV DI Service Manual

DTCs (Diagnostic Trouble Codes) General Description

Oil-Water Separator Switch

(1) P1151/0: Oil-Water Separator Alarm

DTC Detecting Conditions

Movement at Error occurrence

Estimation of Failure cause/Error condition

• The oil-water separator may be malfunctioning.

• Wiring defect of the harness

•

The oil-water separator switch wiring may be short-circuited with GND.

• The oil-water separator switch may be faulty.

•

Inner wiring of the oil-water separator switch may be short-circuited with GND.

• The E-ECU internal circuitry may be faulty.

DTC

P1151/0

Oil-water separator Alarm

1 - Precondition; 2 - Detecting condition(s);
3 - Flashing pattern of failure indicator

Check points

1. Key switch ON.
2. Oil-water separator switch turns ON after engine has been

started.
* This manual assumes that the contact input is configured as

Normally Open (NO).

3. Three flashes followed by five flashes.

Oil-Water Separator
Harness
Oil-Water Separator Switch
E-ECU

Setting of response to oil-water separator failure

Unavailable

Available

Error Mode

[Run As Is]:
After detecting the error, the system lets
the engine continue to run without any
restrictions.

[Run Under Restrictions]:
The engine continues to run under
restrictions.

Run restricted?

No.

Yes: The system restricts the High idle

speed or engine power.

Recovery
Conditions

No.

Remarks

TNV_DI_SM_A4-Troubleshooting.book 112 ページ２００７年１１月１５日　木曜日　午後５時２７分

Содержание 3TNV82A











































































































































































































































Результаты поиска

Содержание 3TNV82A

Отзывы:

Похожие инструкции для 3TNV82A

Бренды по названию

Популярные бренды

Yanmar 3TNV82A, Руководство по устранению неисправностей

Результаты поиска

Содержание 3TNV82A

Отзывы:

Похожие инструкции для 3TNV82A

Бренды по названию

Популярные бренды