background image

30 

7. When the unit is not to be used for a long time 

or when disposing

 

When the unit is not to be used for a long time or when disposing

 

 

 

Caution

 

 

 

Warning

 

 

When the unit is not going to be used for a long 

time

 

Turn the ELB to off and pull out the power 

cord.

 

 

When disposing the unit

 

Do not leave the unit in the area where 

children may have access.

 

Be sure to remove handles before disposing 

the unit to prevent the doors from locking.

 

In general, dispose the unit as a bulky waste.

 

 

 

Notes about disposition

 

 

Always pay attention to the preservation of the global environment.

 

・ 

We  highly  recommend  taking  the  unit  apart  as  far  as  possible  for  separation  or  recycling  to 

contribute to the preservation of the global environment. Major components and materials for the 

unit are as follows:

 

Names of major 

components

 

Major materials

 

Major exterior components 

 

Exterior

 

Bonderized steel sheet iron, melamine resin baking finish

 

Internal bath

 

Stainless steel SUS304

 

Packing

 

Silicon rubber foam

 

Nameplates

 

Polyethylene (PET) resin film

 

Major electric parts

 

Switches and relays

 

Resin, cupper

 

Boards

 

Glass fiber and other composite parts

 

Pipe heater

 

SUS304

 

Power cord

 

Synthesized rubber sheath, cupper, nickel

 

 

Содержание DG-450C











































Отзывы: