manualshive.com logo in svg

Yamakoyo YK1100, Руководство пользователя, Страница: 15 / 41

Поделиться
Скачать
Yamakoyo YK1100 Скачать руководство пользователя страница 15

  (2) These items should be serviced by your servicing dealer unless you have the proper 
         tools and are mechanically proficient. Refer to manual for service procedures.

REFUELING

With the engine stopped, remove the fuel tank cap and check the fuel level. Refill the 
tank if the fuel level is low.

Refuel in a well-ventilated area before starting the engine. If the engine has been 
running, allow it to cool. Refuel carefully to avoid spilling fuel. Do not fill above the fuel 
strainer shoulder. After refueling, tighten the fuel tank cap securely.

Never refuel the engine inside a building where gasoline fumes may reach flames or 
sparks. Keep gasoline away from appliance pilot lights, barbecues, electric appliances, 
power tools, etc.

Spilled fuel is not only a fire hazard, it causes environmental damage. Wipe up spills 
immediately.

Fuel tank capacities
YK-250/300/400:0.66Gal.(2.5L)
YK-550(E), YK-550(E)L, YK-550(E)R:0.95Gal.(3.6L)
YK-600(E):1.2Gal.(4.5L)
YK-650(E), YK-650(E)L, YK-650(E)R:0.95Gal.(3.6L)
YK-800(E), YK-800(E)L, YK-800(E)R:1.6Gal.(6.0L)
YK-900(E), YK-900(E)L, YK-900(E)R:1.6Gal.(6.0L)
YK-1200(E):1.8Gal.(7.0L)
YK-1100(E), YK-1100(E)L, YK-1300(E), YK-1300(E)L, YK-1500(E), YK-1500(E)L:1.7Gal.(6.5L)

12

WARNING

Gasoline is highly flammable and explosive. You can be 
burned or seriously injured when handling fuel.

Stop the engine and keep heat, sparks, and flame away.
Handle fuel only outdoors.
Wipe up spills immediately.

MAXIMUM FUEL LEVEL

MAINTENANCE

Содержание YK1100










































Отзывы:

Нет отзывов