Yamakawa M2090 M2095, Инструкция по эксплуатации

Страница: 7 / 8

Operation
1. PTY Key (RDS programme selection)
2. TA Key (traffic alert/traffic announcements)
3. AF Key (regional mode)
4. EJECT Key (behind the operating unit)
5. CD shaft (behind the operating unit) slot entrance
6. Operating MODE key (radio/CD/MP3)
7. OPEN Key (opens the operating unit)
8. LCD display board
9. PWR Key (power on/off)
10. SEL Key (sound control)
11. “+” Key (sound control up)
12. “–“ Key (sound control down)
13. BAND (frequency selector) Key (AM/FM)
14. Memory Keys 1-6
15. DISP Key (display mode key)
16. TUNE UP Key (radio station search up)
17. TUNE DOWN Key (radio station search down)
18. APS Key (automatic programme search)
19. PAUSE Key (CD operation)
20. SCAN Key (CD operation)
21. RPT (Repeat) Key (CD operation)
22. SHF (Shuffle) Key (CD operation)
23. Only for CD changer control version (optional)
24. Only for CD changer control version (optional)
25. RESET Key, to reset the unit
26. LED (flashes when operating unit is removed)
27. MUTE Key
28. EQ Key
OPERATING CONTROLS
5
26 25
4
5
When you press and hold down the “SEL” (#10) key for a
few secounds, the following RDS functions will be shown in
the display and can be used.
• “TA SEEK” and “TA ALARM” modes
• “TA SEEK” mode
If the station tuned to is not broadcasting a TP signal
(traffic programme), another station with a TP signal is
automatically searched for. If the TP signal of the current
station is lost, the unit searches for another station with a
TIP signal and the same PI (programme identification).
Using the settings “
RETUNE LONG ” (90 sec.) and
“ RETUNE SHORT ” (30 sec.), you can set how long the
unit waits for a TP signal before it searches for a new
station. If no station with the same PI can be found after
one pass, the unit automatically switches to the next
station with a TP signal.
• “TA ALARM” mode
In this operating mode, the automatic search for another
station with a TP signal or the same PI can be
suppressed. If no TP signal is available from a station (or
when it is interrupted), 2 beep tones will be heard. If the
newly tuned station does not have an RDS signal, “
PI
SEEK ” will be suppressed for a while. If the newly tuned
station is not transmitting an RDS signal, “ PI SEEK ” is
suppressed.
• “MASK DPI” and “MASK ALL” mode
During automatic search for alternative stations, no
attention is paid for a few minutes to alternative
frequencies (AF) which have different identifications (PI)
or do not transmit an RDS signal. In the cases where
alternative frequencies have different identifications or
no RDS signal, but nevertheless have a high field
strength, the unit searches for other alternative
frequencies. For this reason, the radio offers the “
MASK
DPI ” function. Here, during the search for alternative
frequencies any station that does not have an RDS
signal but does have a high field strength is not
masked/considered. In this mode it can happen that
incorrect content is reproduced or long delays occur
when the station in question does not have an RDS
signal but does have a field strength that is too high.
• “MASK DPI” mode
Exclusively masks all alternative frequencies with
different identifications.
• “MASK ALL” mode
Masks all alternative frequencies with different
identifications, no RDS signal and a high field strength.
• “BEEP 2ND”, “BEEP ALL” and “BEEP OFF” function
The volume of the beep tones can be changed using the
“AUDIO C” key (#11) and the “AUDIO
CONTROL –“ key (#12).
• “BEEP 2ND” mode
When this function is activated, a beep tone can be
heard when one of the double function keys is kept
pressed down. Example keys: #13, #14, #18.
• “BEEP ALL” mode
A tone can be heard every time a key is pressed.
• “BEEP OFF” mode
The key tones can be deactivated with this option.
• Displays of the received information
Operate the “ DISP ” key (#15) in order to have the
following information from the station displayed:
• When an RDS signal is received:
Radio mode: –> PS –> CT –> FREQ. –> PTY –>
CDC mode: –> CDC –> CT –> PS –>FREQ. –> PTY –>
CD mode: –> CD –> CT –> PS –>FREQ. –> PTY –>
• When no CT or PTY information is received, “NO
CLOCK” or “NO PTY” is shown in the display.
• When no RDS signal is received:
Radio mode: –> NO CLOCK –> FREQ. –> NO PTY –>
CDC mode: CDC –> CT –>FREQ. –> NO PTY –>
CD mode: CD –> CT –>FREQ. –> NO PTY –>
Each of the displayed value remains displayed for a few
seconds before automatically changing to the first value.
TA SEEK or ALARM PI SOUND or MUTE
MASK DPI or ALL RETUNE L or S
BEEP 2'nd, ALL or OFF
Operation
1 2 3 4 5 6
SEL
SCAN RPT SHF PAUSE
MUTE
EQ
AF
LOUD MONO S-CDP LOC D-DIR ME/CR FUNC
REG AF TA TP PTY EON
ST D-AUD
BAND
MODE
7
TUNE TUNE
8 9
LOUD
ENTER
PTY TA
0
APS
MP3
DISP
VOL VOL
7
2 28
3
14
19 20 21 23 6 17 16
9 13 11 12 10 8
22 24
1
27
15
18