background image

INSTRUMENT AND CONTROL FUNCTIONS

4-8

4

Coolant temperature display

The coolant temperature display indi-
cates the temperature of the coolant.

TIP

When the coolant temperature display
is selected, “C” is displayed for one
second, and then the coolant tempera-
ture is displayed.

NOTICE

ECA10021

Do not continue to operate the en-
gine if it is overheating.

Air intake temperature display

The air intake temperature display indi-
cates the temperature of the air drawn
into the air intake duct. Push the “RE-
SET” button to switch the coolant tem-
perature display to the air intake
temperature display.

TIP

Even if the air intake temperature
is set to be displayed, the coolant
temperature warning light comes
on if the engine overheats.

When the key is turned to “ON”,
the coolant temperature is auto-
matically displayed, even if the air
intake temperature was displayed
prior to turning the key to “OFF”.

When the air intake temperature
display is selected, “A” is displayed
for one second, and then the air in-
take temperature is displayed.

Self-diagnosis device

This model is equipped with a self-diag-
nosis device for various electrical cir-
cuits.
If a problem is detected in any of those
circuits, the engine trouble warning light
will come on and the right display will in-
dicate an error code.
If the right display indicates any error
codes, note the code number, and then
have a Yamaha dealer check the vehi-
cle.

1. Coolant temperature display

TRIP A 

˚F

1

1. Air intake temperature display

TRIP A 

˚F

1

1. Error code display

1

U13S12E0.book  Page 8  Tuesday, September 15, 2009  1:52 PM

Содержание YZFR6Z(C)























































































































Отзывы: