background image

FEATURES

1-3

ET2C01019

FI SYSTEM

The fuel pump delivers fuel to the fuel injector via the fuel filter. The pressure regulator maintains the 
fuel pressure that is applied to the fuel injector at only 324 kPa (3.24 kg/cm

²

, 46.1 psi). Accordingly, 

when the energizing signal from the ECU energizes the fuel injector, the fuel passage opens, causing 
the fuel to be injected into the intake manifold only during the time the passage remains open. There-
fore, the longer the length of time the fuel injector is energized (injection duration), the greater the vol-
ume of fuel that is supplied. Conversely, the shorter the length of time the fuel injector is energized 
(injection duration), the lesser the volume of fuel that is supplied.
The injection duration and the injection timing are controlled by the ECU. Signals that are input from the 
throttle position sensor (for throttle cable pulley), throttle position sensor (for throttle valves), coolant 
temperature sensor, atmospheric pressure sensor, cylinder identification sensor, lean angle sensor, 
crankshaft position sensor, intake air pressure sensor, air temperature sensor, speed sensor and O

2

 

sensor enable the ECU to determine the injection duration. The injection timing is determined through 
the signals from the crankshaft position sensor. As a result, the volume of fuel that is required by the 
engine can be supplied at all times in accordance with the driving conditions.

2

19

18

B

17

15

14

13

12

A

3

1

16

4

11

5

C

8

6 7

9

#3

#1 #2

#4

#3

#1 #2

#4

10

1. Secondary injector
2. Fuel pump
3. Primary injector
4. Cylinder identification sensor
5. ECU (engine control unit)
6. Throttle position sensor (for throttle cable 

pulley)

7. Throttle position sensor (for throttle valves)
8. Speed sensor
9. Air temperature sensor
10.Lean angle sensor
11.O

2

 sensor

12.Catalytic converter
13.Coolant temperature sensor
14.Crankshaft position sensor
15.Intake air pressure sensor
16.Throttle servo motor
17.Throttle body
18.Atmospheric pressure sensor
19.Air filter case

A. Fuel system
B. Air system
C. Control system

Содержание YZFR6C












Отзывы: