manualshive.com logo in svg

Yamaha YZF-R1 2015, Руководство по обслуживанию

Поделиться
Скачать
Yamaha YZF-R1 2015 Скачать руководство пользователя страница 287

ABS (Anti-lock Brake System)

4-70

TIP

Push the lock lever down until a click is heard,
making  sure  that  the  ABS  ECU  coupler  is  in-
stalled securely.

7. Fill:

•

Brake fluid reservoir
(with  the  specified  amount  of  the  specified
brake fluid)

WARNING

EWA17280

• Use only the designated brake fluid. Other

brake fluids may cause the rubber seals to

deteriorate,  causing  leakage  and  poor

brake performance.

• Refill with the same type of brake fluid that

is already in the system. Mixing brake fluids

may result in a harmful chemical reaction,

leading to poor brake performance.

• When  refilling,  be  careful  that  water  does

not enter the brake master cylinder reser-

voir or brake fluid reservoir. Water will sig-

nificantly  lower  the  boiling  point  of  the

brake fluid and could cause vapor lock.

NOTICE

ECA13540

Brake  fluid  may  damage  painted  surfaces

and plastic parts. Therefore, always clean up

any spilt brake fluid immediately.

8. Bleed:

•

Brake system
Refer  to  “BLEEDING  THE  HYDRAULIC
BRAKE SYSTEM (ABS)” on page 3-16.

9. Check the operation of the hydraulic unit ac-

cording to the brake lever and the brake ped-
al  response.  (Refer  to  “HYDRAULIC  UNIT
OPERATION TEST” on page 4-70.)

NOTICE

ECA14770

Always check the operation of the hydraulic

unit  according  to  the  brake  lever  and  the

brake pedal response.

10.Delete  the fault codes. (Refer to  “[B-3]  DE-

LETING  THE  FAULT  CODES”  on  page
8-150.)

11.Perform  a  trial  run.  (Refer  to  “CHECKING

THE ABS WARNING LIGHT” on page 4-73.)

EAS30201

HYDRAULIC UNIT OPERATION TEST

The reaction-force pulsating action generated in
the brake lever and brake pedal when the ABS
is  activated  can  be  tested  when  the  vehicle  is
stopped.
The hydraulic unit operation can be tested using
the following two methods.

•

Brake  line  routing  confirmation:  this  test
checks the function of the ABS after the sys-
tem was disassembled, adjusted, or serviced.

•

ABS reaction-force confirmation: this test gen-
erates the same reaction-force pulsating action
that is generated in the brake lever and brake
pedal when the ABS is activated.

Brake line routing confirmation

WARNING

EWA13120

Securely support the vehicle so that there is

no danger of it falling over.

TIP

•

For the brake line routing confirmation, use the
diagnosis mode of the Yamaha diagnostic tool.

•

Before performing the brake line routing confir-
mation, make sure that no malfunctions have
been  detected  in  the  ABS  ECU  and  that  the
wheels are not rotating.

1. Place the vehicle on a suitable stand.
2. Turn the main switch to “OFF”.
3. Remove:

•

Passenger seat/Rider seat
Refer to “GENERAL CHASSIS (1)” on page
4-1.

4. Check:

•

Battery voltage
Lower than 12.8 V 

o

 Charge or replace the

battery.

TIP

If the battery voltage is lower than 12.8 V, charge
the battery, and then perform brake line routing
confirmation.

Specified brake fluid

DOT 4

1

Battery voltage

Higher than 12.8 V

Содержание YZF-R1 2015

































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды