Yamaha YZ450F 2021 Скачать руководство пользователя страница 202

Страница: 202 / 368

CAMSHAFT

5-16

EAM30081

CHECKING THE CAMSHAFT

1. Check:

•

Camshaft lobe
Blue discoloration/pitting/scratches



Re-

place the camshaft.

2. Measure:

•

Camshaft lobe dimensions “A”
Out of specification



Replace the camshaft.

3. Measure:

•

Camshaft runout
Out of specification



Replace.

4. Measure:

•

Camshaft-journal-to-camshaft-cap clearance
Out of specification



Measure the camshaft

journal diameter.

a. Install the camshaft into the cylinder head.
b. Position a strip of Plastigauge® “1” onto

the camshaft journal as shown.

c. Install the dowel pins and the camshaft

caps.

TIP

•

Tighten the camshaft cap bolts in a crisscross
pattern from innermost to outer caps.

•

Do not turn the camshaft when measuring the
camshaft journal-to-camshaft cap clearance.

d. Remove the camshaft caps and then mea-

sure the width of the Plastigauge® “1”.

5. Measure:

•

Camshaft journal diameter “a”
Out of specification



Replace the camshaft.

Within specification



Replace the cylinder

head and the camshaft caps as a set.

Camshaft lobe dimensions

Lobe height limit (Intake)

38.030 mm (1.4972 in)

Lobe height limit (Exhaust)

34.170 mm (1.3453 in)

Camshaft runout limit

0.030 mm (0.0012 in)

Camshaft-journal-to-camshaft-

cap clearance

0.028–0.062 mm (0.0011–0.0024

in)

Camshaft cap bolt

10 N·m (1.0 kgf·m, 7.4 lb·ft)

Содержание YZ450F 2021

















































































































































































































































































































































































Результаты поиска

Содержание YZ450F 2021

Отзывы:

Похожие инструкции для YZ450F 2021

Бренды по названию

Популярные бренды

Yamaha YZ450F 2021, Руководство по эксплуатации для владельца

Результаты поиска

Содержание YZ450F 2021

Отзывы:

Похожие инструкции для YZ450F 2021

Бренды по названию

Популярные бренды