Yamaha YZ 2023 Series Скачать руководство пользователя страница 361

Страница: 361 / 378

SELF-DIAGNOSTIC FUNCTION AND DIAGNOSTIC CODE TABLE

9-14

1: Symbols used in the explanations of the malfunction history



: Normal



: There is currently a malfunction or abnormal condition.



: A malfunction or abnormal condition occurred previously, but the affected system or component is

currently operating normally.

EAM30426

DIAGNOSTIC CODE: ACTUATOR OPERATION TABLE

Setting map erasure

Displays the presence or

absence of the setting history by

Power Tuner.

Erase all setting maps by the

operation start processing.

•

There is no setting.

•

There is some setting.

•

Program version number

Displays a program version No.

—

Diag-

nostic

code

No.

Item

Actuation

Procedure

Ignition coil

Actuates the ignition coil five

times at one-second intervals.

“WARNING” on the Yamaha

diagnostic tool blinks five times

when the ignition coil is actu-

ated.

Check that a spark is gener-

ated five times.

•

Connect an ignition checker.

Injector

Actuates the injector five times

at one-second intervals.

“WARNING” on the Yamaha

diagnostic tool blinks five times

when the injector is actuated.

TIP: Before performing this

operation, be sure to dis-

connect the fuel pump cou-

pler.

Check that injector is actuated

five times by listening for the

operating sound.

Radiator fan motor relay

Actuates the radiator fan motor

relay five times at five-second

intervals.

“WARNING” on the Yamaha

diagnostic tool blinks five times

when the radiator fan motor

relay is actuated.

Check that the radiator fan

motor relay is actuated five

times by listening for the oper-

ating sound.

Diag-

nostic

code

No.

Item

Display

Procedure

Содержание YZ 2023 Series



























































































































































































































































































































































































Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды

Yamaha YZ 2023 Series, Руководство по эксплуатации для владельца

Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды