Yamaha YXZ 1000RSS Скачать руководство пользователя страница 163 | Manualshive

Страница: 163 / 220

Yamaha YXZ 1000RSS Скачать руководство пользователя страница 163

8-34

8

TIP



GL-4 is a quality and additive rating; GL-5
rated hypoid gear oils may also be used.



If desired, an SAE 80W-90 hypoid gear oil
may be used instead.

6. Check the oil filler bolt gasket for dam-

age, and replace it if necessary.

7. Install the differential gear oil filler bolt

and its gasket, and then tighten the bolt
to the specified torque.

8. Check for oil leakage. If oil leakage is

found, check for the cause.

EBU35111

Coolant

The coolant level should be checked regular-
ly. In addition, the coolant must be changed
at the intervals specified in the periodic main-
tenance chart.

TIP

If genuine Yamaha coolant is not available,
use an ethylene glycol antifreeze containing
corrosion inhibitors for aluminum engines and
mix with distilled water at a 1:1 ratio.

Tightening torque:

Differential gear oil filler bolt:

23 N·m (2.3 kgf·m, 17 lb·ft)

Recommended coolant:

YAMALUBE coolant

Coolant quantity:

Coolant reservoir (up to full level):

0.31 L (0.33 US qt, 0.28 Imp.qt)

Radiator (including all routes):

3.75 L (3.96 US qt, 3.30 Imp.qt)

UB0F10E0.book Page 34 Friday, October 27, 2017 2:03 PM

«
...
161
162
163
164
165
...
»

Содержание YXZ 1000RSS





























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды