Yamaha YSP-1600, Руководство по обслуживанию

Страница: 56 / 103

Pin
No.
Port Name
Function Name
(P.C.B.)
I/O
Detail of Function
P
o
w
er ON / [All]
Standb
y / [CEC] /
(BT) /
“HDMI”
When the po
w
er is
tur
ned on
98 SDA1 HDMI_SDA SIO HiZ HDMI RX/TX I2C data input/output
PG0/SDA1/TB7IN0 [SIO] P/U 2.2 k-ohms to +3.3H in P.C.B. INPUT
99 SCL1 HDMI_SCL SIO HiZ HDMI RX/TX I2C clock output
PG1/SCL1/TB7IN1 [SIO] P/U 2.2 k-ohms to +3.3H in P.C.B. INPUT
100 PG2 HDMI_N_RST O O HDMI reset output
PG2/SCK1/CS0n [O]
101 INT6 HDMI_N_INT IRQ HiZ HDMI interrupt input
PG3/INT6/CS1 [IRQ] P/U 10 k-ohms to +3.3H in P.C.B. INPUT
102 PG4 DAMP_N_OTW I HiZ DAMP temperature protection input
PG4/SDA2/TB9IN0 P/U 10 k-ohms to +3.3D in P.C.B. MAIN
103 PG5 PWM_N_MUTE O O PWM_MOD mute output
PG5/SCL2/TB9IN1 P/D in P.C.B. MAIN
104 PG6 PWM_N_RST O O PWM_MOD reset output
PG6/SCK2/CS3n P/D in P.C.B. MAIN
105 INT7 HDMI_MUTE IRQ HiZ HDMI mute input
PG7/INT7/WDTOUTn [IRQ]
106 SDA3 PWM_SDA SIO, PWM_MOD I2C data input/output
PH0/SDA3/TBAIN0 HiZ P/U 10 k-ohms to +3.3D in P.C.B. MAIN
107 SCL3 PWM_SCL SIO HiZ PWM_MOD I2C clock output
PH1/SCL3/SI3/TBAIN0 P/U 10 k-ohms to +3.3D in P.C.B. MAIN
108 PH2 PWM_N_PDN O O PWM_MOD power down output
PH2/SCK3/TBBIN0
109 INTC HDMI_N_INTT IRQ HiZ HDMI TX interrupt input
PH3/INTC/TBBIN1 [IRQ] P/U 10 k-ohms in P.C.B. INPUT (HDMI side)
110 SDA4 O O
PH4/SDA4/TBDIN0
111 SCL4 O O
PH5/SCL4/TBDIN1
112 PH6 O O
PH6/SCK4/TBEIN0
113 INTD REM_IN IRQ IRQ Remote control input signal
PH7/INTD/TBEIN1
114 REGVCC3 REGVCC3 MCU
115 XT1 XT1 MCU Low speed (32 kHz) oscillator connection terminal (input)
116 XT2 XT2 MCU Low speed (32 kHz) oscillator connection terminal (output)
117 CVCC3 CVCC3 MCU
118 X1 X1 MCU High speed (10 MHz) oscillator connection terminal (input)
119 CVSS CVSS [MCU]
120 X2 X2 MCU High speed (10 MHz) oscillator connection terminal (output)
121 DVCC3 DVCC3 MCU
122 REGVSS REGVSS [MCU]
123 INTE STBY_N_SW IRQ IRQ Input for power supply ON/OFF switch detection
PI2/INTE P/U 10 k-ohms to S3.3 in P.C.B. INPUT
124 INTF PDET IRQ IRQ Interrupt input for AC disconnect/connect detected
PI3/INTF P/U to S3.3 in P.C.B. POWER
125 NMIn NMIn IRQ IRQ P/U 10 k-ohms in P.C.B. INPUT
NMIn
126 TEST1 TEST1
TEST1
127 TEST2 TEST2
TEST2
128 BOOTn FLASH_N_BOOT I I FLASH single boot mode input / L: Single boot mode
PI0/B00Tn P/U 47 k-ohms in P.C.B. INPUT
129 CEC HDMI_CEC SIO O HDMI CEC data input/output
PI1/CEC "SIO"
130 AVCC3 AVCC3 MCU
131 AIN0 KEY AD AD KEY input
PJ0/AIN0 P/U 10 k-ohms to S3.3 in P.C.B. INPUT
132 PJ1 HiZ HiZ
PJ1/AIN1
133 PJ2 HiZ HiZ
PJ2/AIN2
56
YSP-1600
Y
SP-1
60
0
DRAFT