Yamaha YP125R Скачать руководство пользователя

Страница: 215 / 498

REAR BRAKE

4-40

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Blow compressed air into the brake hose joint

opening “a” to force out the pistons from the
brake caliper.

WARNING

EWA13550

• Cover the brake caliper piston with a rag.

Be careful not to get injured when the pis-
ton is expelled from the brake caliper.

• Never try to pry out the brake caliper pis-

ton.

b. Remove the brake caliper piston dust seals

and brake caliper piston seals.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

EAS37P1132

CHECKING THE REAR BRAKE CALIPER
(YP125R)

1. Check:

• Brake caliper pistons “1”

Rust/scratches/wear

→

Replace the brake

caliper assembly.

• Brake caliper body “2”

Cracks/damage

→

Replace the brake caliper

assembly.

• Brake fluid delivery passages

(brake caliper body)
Obstruction

→

Blow out with compressed air.

EAS22640

CHECKING THE REAR BRAKE CALIPER
(YP250R)

1. Check:

• Brake caliper pistons “1”

Rust/scratches/wear

→

Replace the brake

caliper pistons.

• Brake caliper cylinders “2”

Scratches/wear

→

Replace the brake caliper

assembly.

• Brake caliper body “3”

Cracks/damage

→

Replace the brake caliper

assembly.

• Brake fluid delivery passages

(brake caliper body)
Obstruction

→

Blow out with compressed air.

WARNING

EWA37P1014

Whenever a brake caliper is disassembled,
replace the brake caliper piston dust seals
and brake caliper piston seals.

Recommended brake component replace-

ment schedule

Brake pads

If necessary

Brake hose

Every four years

Brake fluid

Every two years and
whenever the brake
is disassembled

Recommended brake component replace-

ment schedule

Brake pads

If necessary

Piston seals

Every two years

Piston dust seals

Every two years

Brake hose

Every four years

Brake fluid

Every two years and
whenever the brake
is disassembled

Содержание YP125R



















































































































































































































































































































































































































































































































Результаты поиска

Содержание YP125R

Отзывы:

Похожие инструкции для YP125R

Бренды по названию

Популярные бренды

Yamaha YP125R, Руководство по обслуживанию

Результаты поиска

Содержание YP125R

Отзывы:

Похожие инструкции для YP125R

Бренды по названию

Популярные бренды