Yamaha YP125R Скачать руководство пользователя

Страница: 198 / 498

FRONT BRAKE

4-23

d. Measure the brake disc deflection.
e. If out of specification, repeat the adjustment

steps until the brake disc deflection is within
specification.

f. If the brake disc deflection cannot be brought

within specification, replace the brake disc.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

6. Install:

• Front wheel

Refer to “FRONT WHEEL” on page 4-9.

EAS22270

REPLACING THE FRONT BRAKE PADS

TIP

When replacing the brake pads, it is not neces-
sary to disconnect the brake hose or disassem-
ble the brake caliper.

1. Measure:

• Brake pad wear limit “a”

Out of specification

→

Replace the brake

pads as a set.

2. Install:

• Brake pad support

• Brake pad spring

• Brake pads

TIP

Always install new brake pads, a new brake pad
spring, and a new brake pad support as a set.

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Connect a clear plastic hose “1” tightly to the

bleed screw “2”. Put the other end of the hose
into an open container.

b. Loosen the bleed screw and push the brake

caliper pistons into the brake caliper with your
finger.

c. Tighten the bleed screw.

d. Install new brake pad support, new brake pad

spring and new brake pads.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

3. Install:

• Brake pad pin
• Brake pad pin cap
• Front brake caliper
• Speed sensor lead guide
• Front brake caliper bolts

4. Check:

• Brake fluid level

Below the minimum level mark “a”

→

Add the

recommended brake fluid to the proper level.
Refer to “CHECKING THE BRAKE FLUID
LEVEL” on page 3-35.

Brake pad lining thickness (in-
ner)

5.0 mm (0.20 in)

Limit

1.5 mm (0.06 in)

Brake pad lining thickness (out-
er)

5.0 mm (0.20 in)

Limit

1.5 mm (0.06 in)

New

Bleed screw

6 Nm (0.6 m·kgf, 4.3 ft·lbf)

Front brake caliper bolt

40 Nm (4.0 m·kgf, 29 ft·lbf)

Содержание YP125R



















































































































































































































































































































































































































































































































Результаты поиска

Содержание YP125R

Отзывы:

Похожие инструкции для YP125R

Бренды по названию

Популярные бренды

Yamaha YP125R, Руководство по обслуживанию

Результаты поиска

Содержание YP125R

Отзывы:

Похожие инструкции для YP125R

Бренды по названию

Популярные бренды