Yamaha YP125R Скачать руководство пользователя

Страница: 162 / 498

CHASSIS

3-35

EAS21140

CHASSIS

EAS21240

CHECKING THE BRAKE FLUID LEVEL

1. Stand the vehicle on a level surface.

TIP

• Place the vehicle on the centerstand.
• Make sure the vehicle is upright.

2. Check:

• Brake fluid level

Below the minimum level mark “a”

→

Add the

recommended brake fluid to the proper level.

WARNING

EWA13540

• Use only the designated brake fluid. Other

brake fluids may cause the rubber seals to
deteriorate, causing leakage and poor
brake performance.

• Refill with the same type of brake fluid that

is already in the system. Mixing brake fluids
may result in a harmful chemical reaction,
leading to poor brake performance.

• When refilling, be careful that water does

not enter the brake master cylinder reser-
voir. Water will significantly lower the boil-
ing point of the brake fluid and could cause
vapor lock.

NOTICE

ECA13540

Brake fluid may damage painted surfaces
and plastic parts. Therefore, always clean up
any spilt brake fluid immediately.

TIP

In order to ensure a correct reading of the brake
fluid level, make sure the top of the brake fluid
reservoir is horizontal.

EAS21250

CHECKING THE FRONT BRAKE PADS

The following procedure applies to all of the
brake pads.
1. Operate the brake.
2. Check:

• Front brake pad

Wear indicator grooves “a” have almost dis-
appeared

→

Replace the brake pads as a

set.
Refer to “FRONT BRAKE” on page 4-17.

EAS37P1130

CHECKING THE REAR BRAKE PADS
(YP125R)

The following procedure applies to all of the
brake pads.
1. Operate the brake.
2. Check:

• Rear brake pad

Wear limit “a” reached

→

Replace the brake

pads as a set.
Refer to “REAR BRAKE” on page 4-29.

Front brake

Recommended fluid

DOT 4

Rear brake

Recommended fluid

DOT 4

A. Front brake
B. Rear brake

Limit

0.8 mm (0.03 in)

Содержание YP125R



















































































































































































































































































































































































































































































































Результаты поиска

Содержание YP125R

Отзывы:

Похожие инструкции для YP125R

Бренды по названию

Популярные бренды

Yamaha YP125R, Руководство по обслуживанию

Результаты поиска

Содержание YP125R

Отзывы:

Похожие инструкции для YP125R

Бренды по названию

Популярные бренды