Yamaha YFM35FGW Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 155

Yamaha YFM35FGW Скачать руководство пользователя страница 46

6-2

6

4. Shift the drive select lever into the neutral po-

sition. The neutral indicator light should come
on. If the indicator light does not come on,
have a Yamaha dealer check the electrical cir-
cuit.

NOTE:

The engine can be started under the following con-
ditions:

●

The drive select lever is in the neutral position.

●

The rear brake lever is applied with the drive se-
lect lever in any position. However, it is recom-
mended to shift into the neutral position before
starting the engine.

5. Use the starter (choke) in reference to the fig-

ure:

Position (1):

Cold engine start with ambient temperature
below 5 °C (40 °F).

Position (2):

Cold engine start with ambient temperature
between 0 °C (30 °F) and 30 °C (90 °F).

Position (3):

Cold engine start with ambient temperature
above 25 °C (80 °F).

Ambient temp./starter (choke) position

6. Completely close the throttle lever and start

the engine by pushing the start switch.

NOTE:

●

If the engine fails to start, release the start
switch, then push it again. Pause a few seconds
before the next attempt. Each cranking should
be as short as possible to preserve battery ener-
gy. Do not crank the engine more than 10 sec-
onds on each attempt.

1. Fully open

2. Half open

3. Closed
4. Starter (choke)

U5UH14E0.book Page 2 Thursday, April 13, 2006 6:30 PM

«
...
44
45
46
47
48
...
»

Содержание YFM35FGW




























































































































































Отзывы:

Нет отзывов