background image

6-5

6

There is never a more important period in the life of
your engine than the first 320 km (200 mi) or 20
hours of riding. For this reason, you should read
the following material carefully.
Since the engine is brand new, do not put an ex-
cessive load on it for the first 320 km (200 mi) or 20
hours. The various parts in the engine wear and
polish themselves to the correct operating clear-
ances. During this period, prolonged full-throttle
operation or any condition that might result in en-
gine overheating must be avoided.

0–160 km (0–100 mi) or 0–10 hours
Avoid prolonged operation above 1/2 throttle. Vary
the speed of the ATV regularly. Do not operate it at
one set throttle position.

160–320 km (100–200 mi) or 10–20 hours
Avoid prolonged operation above 3/4 throttle. Rev
the engine through the gears freely, but do not use
full throttle at any time.

320 km (200 mi) or 20 hours and beyond
The ATV can now be operated normally.

NOTICE

ECB00220

If any engine trouble should occur during the
engine break-in period, immediately have a
Yamaha dealer check the ATV.

EBU20722

Parking 

When parking the ATV, shift into first gear, stop the
engine, apply the parking brake, and then turn the
fuel cock to “OFF”.

1. Parking brake lever (locked position)

U1BT62E0.book  Page 5  Tuesday, April 19, 2011  7:06 PM

Содержание YFM25RB







































































































































Отзывы: