background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-28

7

EAU23283

Checking the steering 

Worn or loose steering bearings may
cause danger. Therefore, the operation
of the steering must be checked as fol-
lows at the intervals specified in the pe-
riodic maintenance and lubrication
chart.

1. Place a stand under the engine to

raise the front wheel off the
ground. (See page 7-34 for more
information.) 

WARNING! To

avoid injury, securely support
the vehicle so there is no danger
of it falling over.

 [EWA10751]

2. Hold the lower ends of the front

fork legs and try to move them for-
ward and backward. If any free
play can be felt, have a Yamaha
dealer check or repair the steering.

EAU23291

Checking the wheel bearings 

The front and rear wheel bearings must
be checked at the intervals specified in
the periodic maintenance and lubrica-
tion chart. If there is play in the wheel
hub or if the wheel does not turn
smoothly, have a Yamaha dealer check
the wheel bearings.

EAU50710

Battery 

The battery is located under the seat.
(See page 4-13.)
This model is equipped with a VRLA
(Valve Regulated Lead Acid) battery.
There is no need to check the electro-
lyte or to add distilled water. However,
the battery lead connections need to be
checked and, if necessary, tightened.

WARNING

EWA10760

Electrolyte is poisonous and
dangerous since it contains sul-
furic acid, which causes severe
burns. Avoid any contact with

1. Battery

2. Negative battery lead (black)

3. Positive battery lead (red)

1

2

3

U27D11E0.book  Page 28  Monday, July 11, 2011  11:15 AM

Содержание XVS13CB





































































































Отзывы: