Yamaha XVS13AW(C) Скачать руководство пользователя страница 71

Страница: 71 / 97

PERIODIC MAINTENANCE AND MINOR REPAIR

6-32

EAU42470

Replacing the headlight bulb

This model is equipped with a quartz
bulb headlight. If the headlight bulb
burns out, replace it as follows.

1. Remove the turn signal/position

light bracket cover by removing the
bolts.

2. Remove the headlight unit by re-

moving the bolts on each side.

3. Disconnect the headlight coupler,

and then remove the bulb cover.

4. Unhook the headlight bulb holder,

and then remove the defective
bulb.

WARNING

EWA10790

Headlight bulbs get very hot. There-
fore, keep flammable products away
from a lit headlight bulb, and do not
touch the bulb until it has cooled
down.

5. Place a new headlight bulb into po-

sition, and then secure it with the
bulb holder.

CAUTION:

ECA10660

Do not touch the glass part of the
headlight bulb to keep it free from
oil, otherwise the transparency of
the glass, the luminosity of the bulb,

1. Turn signal/position light bracket cover

2. Bolt

1. Bolt

1. Headlight bulb cover

2. Headlight coupler

1. Headlight bulb holder
2. Headlight bulb

U3D810E0.book Page 32 Wednesday, July 19, 2006 11:14 AM

Содержание XVS13AW(C)


































































































Результаты поиска

Содержание XVS13AW(C)

Отзывы:

Похожие инструкции для XVS13AW(C)

Бренды по названию

Популярные бренды

Yamaha XVS13AW(C), Руководство пользователя

Результаты поиска

Содержание XVS13AW(C)

Отзывы:

Похожие инструкции для XVS13AW(C)

Бренды по названию

Популярные бренды