background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-20

6

1. Loosen the locknut at the brake le-

ver.

2. To increase the brake lever free

play, turn the adjusting screw in di-
rection (a). To decrease the brake
lever free play, turn the adjusting
screw in direction (b).

3. Tighten the locknut.

WARNING

EWA10630

After adjusting the brake lever
free play, check the free play
and make sure that the brake is
working properly.

A soft or spongy feeling in the
brake lever can indicate the
presence of air in the hydraulic

system. If there is air in the hy-
draulic system, have a Yamaha
dealer bleed the system before
operating the motorcycle. Air in
the hydraulic system will dimin-
ish the braking performance,
which may result in loss of con-
trol and an accident.

EAU22270

Adjusting the rear brake light 
switch 

The rear brake light switch, which is ac-
tivated by the brake pedal, is properly
adjusted when the brake light comes
on just before braking takes effect. If
necessary, adjust the brake light switch
as follows.
Turn the adjusting nut while holding the
rear brake light switch in place. To
make the brake light come on earlier,
turn the adjusting nut in direction (a). To
make the brake light come on later, turn
the adjusting nut in direction (b).

1. Locknut
2. Brake lever free play adjusting screw

1. Rear brake light switch

2. Rear brake light switch adjusting nut

U3B820E0.book  Page 20  Tuesday, April 12, 2005  9:43 AM

Содержание XVS1100V































































































Отзывы: