Yamaha XT660R Скачать руководство пользователя страница 76

Страница: 76 / 92

PERIODIC MAINTENANCE AND MINOR REPAIR

6-38

XT660X

3. Lift the rear wheel off the ground

according to the procedure on
page 6-35.

4. Loosen the locknut on each side of

the swingarm.

5. Turn the drive chain slack adjust-

ing nuts (or bolts according to the
model) fully in direction (a).

6. Remove the wheel axle by remov-

ing the axle nut.

7. Push the wheel forward, and then

remove the drive chain from the
rear sprocket.

NOTE:

The drive chain cannot be disassem-
bled.

8. Pull the wheel backward and move

the brake caliper away from the
wheel.

CAUTION:

ECA11070

Do not apply the brake after the
wheel has been removed together
with the brake disc, otherwise the
brake pads will be forced shut.

EAUM2140

To install the rear wheel

1. Install the drive chain onto the rear

sprocket.

2. Install the wheel, the washer(s)

and the brake caliper bracket by
inserting the wheel axle from the
left-hand side.

NOTE:

●

XT660R: Install the washer with
the “N” mark on the right-hand side
and the washer with the “O” mark
on the left-hand side. Be sure to in-
stall both washers with their marks
facing outward.

1. Axle nut

2. Drive chain slack adjusting bolt

3. Locknut
4. Brake caliper bracket

5. Brake caliper

(a)

1. Brake caliper
2. Brake disc

U5VKE1E0.book Page 38 Tuesday, July 18, 2006 1:00 PM

Содержание XT660R





























































































Результаты поиска

Содержание XT660R

Отзывы:

Yamaha XT660R, Руководство пользователя, Страница: 76 / 92

Результаты поиска

Содержание XT660R

Отзывы: