Yamaha XT250D страница 41 Скачать руководство пользователя

Страница: 41 / 100

PERIODIC MAINTENANCE AND ADJUSTMENT

7-3

EAU48470

TIP



From 19000 mi (31000 km) or 36 months, repeat the maintenance intervals starting from 7000 mi (11000 km) or 12
months.



Items marked with an asterisk require special tools, data and technical skills, have a Yamaha dealer perform the service.

EAU17581

Periodic maintenance chart for the emission control system

No.

ITEM

ROUTINE

INITIAL

ODOMETER READINGS

600 mi

(1000 km)

1 month

4000 mi

(6000 km)

6 months

7000 mi

(11000 km)

12 months

10000 mi

(16000 km)

18 months

13000 mi

(21000 km)

24 months

16000 mi

(26000 km)

30 months

Fuel line

• Check fuel hoses for cracks or

damage.

• Replace if necessary.



Spark plug

• Check condition.
• Adjust gap and clean.
• Replace at 7000 mi (11000 km)

or 12 months and thereafter
every 6000 mi (10000 km) or 12
months.



Replace.



Replace.



Spark arrester

• Clean.



Valve clearance

• Check and adjust valve

clearance when engine is cold.



Crankcase breather
system

• Check breather hose for cracks

or damage.

• Replace if necessary.



Fuel injection

• Check and adjust engine idle

speed.



1YB-9-10.book 3 ページ２０１２年３月２７日　火曜日　午前１１時３６分

Содержание XT250D





































































































Результаты поиска

Содержание XT250D

Отзывы:

Похожие инструкции для XT250D

Бренды по названию

Популярные бренды

Yamaha XT250D, Руководство пользователя

Результаты поиска

Содержание XT250D

Отзывы:

Похожие инструкции для XT250D

Бренды по названию

Популярные бренды