Yamaha XT250D страница 37 Скачать руководство пользователя | Manualshive

Страница: 37 / 100

background image

OPERATION AND IMPORTANT RIDING POINTS

6-3

2

3

4

5

6

7

8

9

quickly pull the clutch lever in.

5. Shift the transmission into second

gear. (Make sure not to shift the
transmission into the neutral posi-
tion.)

6. Open the throttle part way and

gradually release the clutch lever.

7. Follow the same procedure when

shifting to the next higher gear.

TIP

When shifting gears in normal operat-
ing conditions, use the recommended
shift points.

EAU16700

To decelerate

1. Apply both the front and the rear

brakes to slow the motorcycle.

2. Shift the transmission into first

gear when the motorcycle reaches
20 km/h (12 mi/h). If the engine is
about to stall or runs very roughly,
pull the clutch lever in and use the
brakes to stop the motorcycle.

3. Shift the transmission into the neu-

tral position when the motorcycle
is almost completely stopped. The
neutral indicator light should come

on.

EAU16720

Recommended shift points

The recommended shift points during
acceleration and deceleration are
shown in the table below.

EAU16841

Engine break-in

There is never a more important period
in the life of your engine than the period
between 0 and 1600 km (1000 mi). For
this reason, you should read the follow-
ing material carefully.
Since the engine is brand new, do not
put an excessive load on it for the first
1600 km (1000 mi). The various parts in
the engine wear and polish themselves
to the correct operating clearances.
During this period, prolonged full-throt-
tle operation or any condition that might
result in engine overheating must be
avoided.

EAU17023

0–1000 km (0–600 mi)

Avoid prolonged operation above 1/3
throttle.

NOTICE:

After 1000 km (600

mi) of operation, the engine oil must
be changed, and the oil filter car-
tridge or element replaced.

[ECA11282]

1000–1600 km (600–1000 mi)

Avoid prolonged operation above 1/2

Shift up points:

1st



2nd: 16 km/h (10 mi/h)

2nd



3rd: 24 km/h (15 mi/h)

3rd



4th: 32 km/h (20 mi/h)

4th



5th: 40 km/h (25 mi/h)

Shift down points:

5th



4th: 20 km/h (12 mi/h)

4th



3rd: 20 km/h (12 mi/h)

3rd



2nd: 20 km/h (12 mi/h)

2nd



1st: 20 km/h (12 mi/h)

1YB-9-10.book 3 ページ２０１２年３月２７日　火曜日　午前１１時３６分

«
...
35
36
37
38
39
...
»

Содержание XT250D





































































































Отзывы:

Нет отзывов

Похожие инструкции для XT250D

Scout 25L Pannier Kit V2.0

Бренд: MOSKO MOTO Страницы: 13

Бренд: Memphis Shades Страницы: 2

Бренд: KTM Страницы: 207

Бренд: Britannia Страницы: 9

Бренд: Power Fist Страницы: 2

Бренд: Power Fist Страницы: 16

Бренд: Cagiva Страницы: 124

Бренд: Bagster Страницы: 2

Бренд: RS Motorcycle Solutions Страницы: 3

Бренд: RSI Страницы: 2

Бренд: hepco & becker Страницы: 4

Бренд: R&G Страницы: 20

Бренд: Busse Страницы: 24

RetroRadio BT100

Бренд: Biketronics Страницы: 2

Бренд: KTM Страницы: 26

Бренд: TSG Страницы: 60

Бренд: KTM Страницы: 48

CRF50F 2004-2015

Бренд: Honda Страницы: 209

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды