manualshive.com logo in svg

Yamaha XT250D, Руководство пользователя

Поделиться
Скачать
Yamaha XT250D Скачать руководство пользователя страница 35

6-1

2

3

4

5

6

7

8

9

OPERATION AND IMPORTANT RIDING POINTS

EAU15951

Read the Owner’s Manual carefully to
become familiar with all controls. If
there is a control or function you do not
understand, ask your Yamaha dealer.

WARNING

EWA10271

Failure to familiarize yourself with
the controls can lead to loss of con-
trol, which could cause an accident
or injury.

EAU48020

TIP

This model is equipped with a lean an-
gle sensor to stop the engine in case of
a turnover. In this case, the multi-func-
tion display indicates error code 30, but
this is not a malfunction. Turn the key to
“OFF” and then to “ON” to clear the er-
ror code. Failing to do so will prevent
the engine from starting even though
the engine will crank when pushing the
start switch.

EAU16247

Starting the engine 

In order for the ignition circuit cut-off
system to enable starting, one of the
following conditions must be met:

The transmission is in the neutral
position.

The transmission is in gear with
the clutch lever pulled and the sid-
estand up.
See page 4-12 for more informa-
tion.

1. Turn the key to “ON” and make

sure that the engine stop switch is
set to “

”.

The following warning lights
should come on for a few seconds,
then go off.

Fuel level warning light

Engine trouble warning light

NOTICE

ECA15484

If a warning light does not come on
initially when the key is turned to
“ON”, or if a warning light remains
on, see page 4-2 for the correspond-
ing warning light circuit check.

2. Shift the transmission into the neu-

tral position. The neutral indicator

1YB-9-10.book  1 ページ  ２０１２年３月２７日　火曜日　午前１１時３６分

Содержание XT250D





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды