Yamaha XT250D Скачать руководство пользователя | Manualshive

Страница: 31 / 100

background image

INSTRUMENT AND CONTROL FUNCTIONS

4-12

2

3

4

5

6

7

8

9

EAU15305

Sidestand

The sidestand is located on the left side
of the frame. Raise the sidestand or
lower it with your foot while holding the
vehicle upright.

TIP

The built-in sidestand switch is part of
the ignition circuit cut-off system, which
cuts the ignition in certain situations.
(See the following section for an expla-
nation of the ignition circuit cut-off sys-
tem.)

WARNING

EWA10241

The vehicle must not be ridden with
the sidestand down, or if the side-
stand cannot be properly moved up
(or does not stay up), otherwise the
sidestand could contact the ground
and distract the operator, resulting
in a possible loss of control.
Yamaha’s ignition circuit cut-off
system has been designed to assist
the operator in fulfilling the respon-
sibility of raising the sidestand be-
fore starting off. Therefore, check
this system regularly and have a

Yamaha dealer repair it if it does not
function properly.

EAU15314

Ignition circuit cut-off system

The ignition circuit cut-off system (com-
prising the sidestand switch, clutch
switch and neutral switch) has the fol-
lowing functions.



It prevents starting when the trans-
mission is in gear and the side-
stand is up, but the clutch lever is
not pulled.



It prevents starting when the trans-
mission is in gear and the clutch le-
ver is pulled, but the sidestand is
still down.



It cuts the running engine when the
transmission is in gear and the sid-
estand is moved down.

Periodically check the operation of the
ignition circuit cut-off system according
to the following procedure.

TIP

This check is most reliable if performed
with a warmed-up engine.

1YB-9-10.book 12 ページ２０１２年３月２７日　火曜日　午前１１時３６分

«
...
29
30
31
32
33
...
»

Содержание XT250D





































































































Отзывы:

Нет отзывов

Похожие инструкции для XT250D

Бренд: Kabuto Страницы: 25

Бренд: X-lite Страницы: 5

Бренд: Yamaha Страницы: 86

Бренд: Yamaha Страницы: 57

Бренд: Yamaha Страницы: 288

TRACER 700 2020

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 118

XV1700PCR Road Star Warrior

Бренд: Yamaha Страницы: 122

Бренд: Yamaha Страницы: 429

Бренд: Yamaha Страницы: 427

Moto matrix YZF-R6S

Бренд: Yamaha Страницы: 41

Бренд: hepco & becker Страницы: 4

Бренд: Cobra Страницы: 2

Advanced Million Color Mini Motorcycle Lighting Kit

Бренд: LedGlow Страницы: 3

Saddle Tramp BC-BTHBSP

Бренд: Metra Electronics Страницы: 8

Turismo Veloce 800 LUSSO

Бренд: AGUSTA Страницы: 616

Бренд: Ohlins Страницы: 4

Бренд: GYS Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды