Yamaha WR250F 2022 Скачать руководство пользователя страница 360

Страница: 360 / 404

ELECTRICAL COMPONENTS

8-59

EAM30357

CHECKING THE BULBS AND BULB

SOCKETS

1. Remove:

•

Bulb

NOTICE

ECA25930

Be sure to hold the socket firmly when re-

moving the bulb. Never pull the lead, other-

wise it may be pulled out of the terminal in

the coupler.

2. Check:

•

Bulb (for continuity)
(with the digital circuit tester)
No continuity



Replace.

TIP

Before checking for continuity, set the digital cir-
cuit tester to “



” range.

3. Check:

•

Bulb socket (for continuity)
(with the digital circuit tester)
No continuity



Replace.

TIP

Check each bulb socket for continuity in the
same manner as described in the bulb section;
however, note the following.

a. Install a good bulb into the bulb socket.
b. Connect the digital circuit tester probes to

the respective leads of the bulb socket.

c. Check the bulb socket for continuity. If any

of the readings indicate no continuity, re-
place the bulb socket.

EAM30290

CHECKING THE FUSES

The following procedure applies to all of the fus-
es.
1. Remove:

•

Seat
Refer to “GENERAL CHASSIS” on page 4-1.

2. Check:

•

Main fuse “1”

•

Radiator fan motor fuse “2”

a. Connect the digital circuit tester to the fuse

and check the continuity.

TIP

Set the digital circuit tester selector to “



”.

b. If the digital circuit tester indicates “O.L”,

replace the fuse.

3. Replace:

•

Fuse
a. Install a new fuse of the correct amperage

rating.

b. Push the start switch to verify if the electri-

cal circuit is operational.

c. If the fuse immediately blows again, check

the electrical circuit.

WARNING

EWA13310

Never use a fuse with an amperage rating

other than that specified. Improvising or us-

ing a fuse with the wrong amperage rating

may cause extensive damage to the electri-

cal system, cause the lighting and ignition

systems to malfunction and could possibly

cause a fire.

4. Install:

•

Seat

Digital circuit tester (CD732)

90890-03243

Model 88 Multimeter with tachom-

eter

YU-A1927

Digital circuit tester (CD732)

90890-03243

Model 88 Multimeter with tachom-

eter

YU-A1927

Digital circuit tester (CD732)

90890-03243

Model 88 Multimeter with tachom-

eter

YU-A1927

Fuses

Amperage

rating

Q’ty

Main

15 A

Spare

15 A

Radiator fan motor

5 A

Содержание WR250F 2022





















































































































































































































































































































































































































Результаты поиска

Содержание WR250F 2022

Отзывы:

Похожие инструкции для WR250F 2022

Бренды по названию

Популярные бренды

Yamaha WR250F 2022, Руководство по эксплуатации для владельца

Результаты поиска

Содержание WR250F 2022

Отзывы:

Похожие инструкции для WR250F 2022

Бренды по названию

Популярные бренды