Yamaha WOLVERINE YFM35XW Скачать руководство пользователя

Страница: 110 / 146

8-29

●

Before adjusting the brake lever and brake pedal
free play, check the rear brake shoes for wear.

Adjusting the brake pedal free play

The brake pedal free play should measure 20.0–
30.0 mm (0.79–1.18 in) as shown. If the free play
is incorrect, adjust it as follows.

1. Fully loosen the brake lever free play adjust-

ing nut on the brake cable at the rear wheel
hub.

2. Turn the brake pedal free play adjusting nut

on the brake cable at the rear wheel hub in di-
rection (a) to increase the free play, and in di-
rection (b) to decrease it.

Adjusting the brake lever free play

The brake lever free play should measure 3.0–5.0
mm (0.12–0.20 in) as shown. If the free play is in-
correct, adjust it as follows.

1. Brake pedal free play

1. Brake lever free play adjusting nut
2. Brake pedal free play adjusting nut

U3D510E0.book Page 29 Friday, December 2, 2005 1:07 PM

Содержание WOLVERINE YFM35XW



















































































































































Результаты поиска

Содержание WOLVERINE YFM35XW

Отзывы:

Похожие инструкции для WOLVERINE YFM35XW

Бренды по названию

Популярные бренды

Yamaha WOLVERINE YFM35XW, Руководство пользователя

Результаты поиска

Содержание WOLVERINE YFM35XW

Отзывы:

Похожие инструкции для WOLVERINE YFM35XW

Бренды по названию

Популярные бренды