Yamaha WaveRunner VX Cruiser 2007 страница 90 Скачать руководство пользователя | Manualshive

Страница: 90 / 96

background image

Trouble recovery

83

CAUTION:

ECJ00660

●

Place a suitable clean cloth or carpeting
underneath the watercraft to protect it
from abrasions and scratches.

●

Always turn the watercraft over onto its
port (left) side.

●

When turning the watercraft on its side,
support the bow so that the handlebars
are not bent or damaged.

(2) Remove any weeds or debris from

around the drive shaft, impeller, jet pump
housing, and jet thrust nozzle.
If debris is difficult to remove, consult a
Yamaha dealer.

CAUTION:

ECJ00670

Always avoid operating your watercraft in
areas where weed growth is thick. If travel-
ing in weeded areas is unavoidable, oper-
ate the engine alternately at partial throttle
and full throttle. Weeds tend to accumu-
late more at a steady speed and at trolling
speed. If weeds clog the jet intake or im-
peller area and cause cavitation, follow the
cleaning procedure above.

EJU34640

Jumping the battery

If the watercraft battery has run down, the en-
gine can be started using a 12-volt booster
battery and jumper cables.

WARNING

EWJ00790

Battery electrolyte is poisonous and dan-
gerous, causing severe burns, etc. Elec-
trolyte contains sulfuric acid. Avoid
contact with skin, eyes, or clothing.
Antidotes
External: Flush with water.
Internal: Drink large quantities of water or
milk. Follow with milk of magnesia, beaten

egg, or vegetable oil. Call a physician im-
mediately.
Eyes: Flush with water for 15 minutes and
get prompt medical attention.
Batteries produce explosive gases. Keep
sparks, flames, cigarettes, etc., well away.
If using or charging the battery in an en-
closed space, make sure that it is well ven-
tilated. Always shield your eyes when
working near batteries.
KEEP OUT OF THE REACH OF CHILDREN.

EJU34660

Connecting the jumper cables

(1) Connect the positive (+) jumper cable to

the positive (+) battery terminals of both
batteries.

(2) Connect one end of the negative (–)

jumper cable to the negative (–) battery
terminal of the booster battery.

(3) Connect the other end of the negative (–)

jumper cable to an engine hanger.

CAUTION:

ECJ00680

Do not connect the end of the negative (–)
jumper cable to the negative (–) battery
terminal of the watercraft battery! Make
sure that all connections are secure and
correct before attempting to start the en-

1

Positive (+) jumper cable

2

Negative (–) jumper cable

3

Booster battery

4

Engine hanger

UF1K72E0.book Page 83 Wednesday, August 2, 2006 10:43 AM

«
...
88
89
90
91
92
...
»

Содержание WaveRunner VX Cruiser 2007

































































































Отзывы:

Нет отзывов

Похожие инструкции для WaveRunner VX Cruiser 2007

Бренд: Jeanneau Страницы: 80

CASCADE BT-21CAP

Бренд: Aqua-Marina Страницы: 68

Бренд: Mercury Страницы: 155

Бренд: Prestige Страницы: 110

Бренд: Pelican Страницы: 12

Бренд: Jensen Marine Страницы: 22

Бренд: Camper & Nicholson Страницы: 22

Бренд: Feathercraft Страницы: 23

Grand Soleil 50

Бренд: Cantiere Del Pardo Страницы: 124

Бренд: Yamaha Страницы: 122

GP1300R WaveRunner 2003

Бренд: Yamaha Страницы: 279

Бренд: Duffy Страницы: 16

Бренд: Castaway Boats Страницы: 32

Бренд: Silver Страницы: 278

Бренд: Sportsman Страницы: 33

DISCOVERY 210DC

Бренд: Sportsman Страницы: 30

Бренд: Sportsman Страницы: 41

Бренд: Sportsman Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды