Yamaha TW200 ET 2005 Скачать руководство пользователя страница 71

Страница: 71 / 86

PERIODIC MAINTENANCE AND MINOR REPAIR

6-36

4. Lift the rear wheel off the ground

according to the procedure on
page 6-33.

5. Remove the axle nut, and then pull

the wheel axle out.

6. Push the wheel forward, and then

remove the drive chain from the
rear sprocket.

NOTE:

The drive chain does not need to be
disassembled in order to remove and

install the wheel.

7. Remove the wheel.

EAU25761

To install the rear wheel

1. Insert the wheel axle from the

left-hand side.

NOTE:

Make sure that the drive chain adjust-
ing plates are installed with the
punched sides facing to the outside
and that the slot in the brake shoe plate

fits over the retainer on the swingarm.

2. Install the drive chain onto the rear

sprocket, and then adjust the drive
chain slack. (See page 6-22.)

3. Install the axle nut, and then lower

the rear wheel so that it is on the
ground.

4. Tighten the axle nut to the speci-

fied torque.

5. Install the brake rod onto the brake

camshaft lever, and then install the
brake pedal free play adjusting nut
onto the brake rod.

6. Adjust the brake pedal free play.

(See page 6-18.)

WARNING

EWA10660

After adjusting the brake pedal free
play, check the operation of the

brake light.

1. Axle nut
2. Brake pedal free play adjusting nut
3. Brake rod
4. Brake camshaft lever
5. Drive chain slack adjusting plate

(a)

1. Retainer

Tightening torque:

Axle nut:

90 Nm (9.0 m·kgf, 65 ft·lbf)

Содержание TW200 ET 2005























































































Результаты поиска

Содержание TW200 ET 2005

Отзывы:

Похожие инструкции для TW200 ET 2005

Бренды по названию

Популярные бренды

Yamaha TW200 ET 2005, Руководство пользователя

Результаты поиска

Содержание TW200 ET 2005

Отзывы:

Похожие инструкции для TW200 ET 2005

Бренды по названию

Популярные бренды