Yamaha TT-R230 2020 Скачать руководство пользователя страница 22

Страница: 22 / 80

Instrument an

control functions

4-6

EAU13601

Starter (choke) kno

“ ”

Starting a cold engine requires a richer
air-fuel mixture, which is supplied by
the starter (choke).
Move the knob in direction (a) to turn
on the starter (choke).
Move the knob in direction (b) to turn
off the starter (choke).

EAU13962

Seat

To remove the seat

Remove the bolts, and then pull the
seat off.

To install the seat

1. Insert the projections on the front

of the seat into the seat holders as
shown.

2. Place the seat in the original posi-

tion, and then tighten the bolts.

TIP

Make sure that the seat is properly se-
cured before riding.

1. Starter (choke) knob “

”

1. Bolt

1. Projection
2. Seat holder

UB6816E0.book Page 6 Thursday, April 2, 2020 9:26 AM

Содержание TT-R230 2020

















































































Результаты поиска

Содержание TT-R230 2020

Отзывы:

Похожие инструкции для TT-R230 2020

Бренды по названию

Популярные бренды

Yamaha TT-R230 2020, Руководство пользователя

Результаты поиска

Содержание TT-R230 2020

Отзывы:

Похожие инструкции для TT-R230 2020

Бренды по названию

Популярные бренды