■
Specifications
■
Part Names
■
Connections
Use the supplied stereo phone cable to connect the pad's output jack with the input jack
(SNARE, TOM 1, etc.) on the drum trigger module (DTXPRESS/DTX/DTXTREME). Con-
nect the cable's L-shaped plug to the TP65/65S.
❇
Connect to the input that is used for the tom pad on your drum trigger module. (Refer to the Owner's
Manual that came with the drum trigger module for further information.)
❇
Make sure that a stereo cable is used when connecting the TP65S to the module. If a monaural cable
(Plug has one black rings) is used, the voices set to the right/left rim will not be produced.
Pad
TP65
TP65S
Output jack
Clamp Bolt
Right Rim
Left Rim
Pad
(The TP65S contains switches in its left and right rim sections.)
Output jack
Insert
The manner in which the TP65/65S will function corresponds to the INPUT numbers on the
DTX Series Drum Trigger Module shown in the chart below.
Adjusting the Voice Volume
To change the volume of the voice(s) assigned to the TP65/65S, use the [VOICE] Edit
Mode in the DTX Series Drum Trigger Module. Please refer to the Owner's Manual
that came with your module for further information.
Printed in Indonesia
WF75880
SPECIAL MESSAGE SECTION
NOTICE:
Service charges incurred due to a lack of knowledge relathing to how a function or effect works (when the unit is operating
as designed) are not covered by the manufacturer’s warranty, and are therefore the owners responsibility. Please study this manual
carefuly and consult your dealer before requesting service.
ENVIRONMENTAL ISSUES:
Yamaha strives to produce products that are both user safe and environmentally friendly. We sincerely
believe that our products and the production methods used to produce them, meet these goals. In keeping with both the letter and the
spirit of the law, we want you to be aware of the following:
Warning:
Do not attempt to disassemble.
Disposal Notice:
Should this product become damaged beyond repair, or for some reason its useful life is considered to be at an end,
please observe all local, state, and federal regulations that relate to the disposal of products that contain lead, plastics, etc. If your
dealer is unable to assist you, please contact Yamaha directly.
NAME PLATE LOCATIOIN
: The name plate is located on the bottom of the product. The model number, serial number are located on
this plate.
You should record the model number, serial number, and the date of purchase in the spaces provided below and retain this manual as
a permanent record of your purchase.
Model : TP65 Serial No.
Model : TP65S Serial No.
Purchase Date
PLEASE KEEP THIS MANUAL
* Improvements may result in a change in the specifications and/or design of the product without notice.
Dimensions
Weight
Sensor System
Output Jack
220(diameter) X 61(H) (excluding the clamp bolt)
980g (including the clamp bolt)
TP65: Trigger Sensor (piezo-electric) x1
Trigger Sensor (piezo-electric) x1/
Rim switch (2 zones) x1
Standard Monaural Phone Jack
Standard Stereo Phone Jack
TP65
TP65S
■
Setting Up
Tom Holder
Clamp Bolt
Insert
After setting up your rack system (Yamaha RS70, etc.) or a standard tom stand (Yamaha
WS series, etc.), attach the TP65/65S as shown in the diagram below.
Insert the tom holder (hexagonal bar) on your rack or tom stand into the pad, and firmly
tighten the clamp bolt to secure.
MODULE
Input Number
TP65 TP65S
DTXTREME s
1〜8
●
◎
9/10〜15/16
●
●
DTXPRESS
1
●
△
DTXPRESS
2,6,7
●
◎
3〜5,8
●
○
9/10
●
●
DTXTREME
1〜5
●
△
6〜8
●
○
9/10〜15/16
●
●
DTXPRESS
1
●
△
2〜8
●
○
9/10
●
●
DTX
1〜8
●
○
9/10,11/12
●
●
● ：
A single voice is assigned to, and produced by the pad.
○ ：
Individual voices can be assigned to, and produced by the pad
and rim (2 voices).
◎ ：
Individual voices can be assigned to, and produced by the pad,
left rim, and right
rim (3 voices).
△ ：
Individual voices can be assigned to, and produced by the pad,
and right rim (2 voices: the left rim switch is inactive).