Yamaha STRATOLINER XV19CTSV Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 100

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-20

6

EAU22750

Changing the brake and
clutch fluids

Have a Yamaha dealer change the
brake and clutch fluids at the intervals
specified in the NOTE after the periodic
maintenance and lubrication chart. In
addition, have the oil seals of the brake
and clutch master cylinders and cali-
pers as well as the brake and clutch
hoses replaced at the intervals listed
below or whenever they are damaged
or leaking.

●

Oil seals: Replace every two
years.

●

Brake and clutch hoses: Replace
every four years.

EAU23040

Drive belt slack

The drive belt slack should be checked
and adjusted at the intervals specified
in the periodic maintenance and lubri-
cation chart.

EAU38410

To check the drive belt slack

1. Place the vehicle on the sidestand.
2. Note the current position of the

drive belt using the marks near the
drive belt check hole.

NOTE:

The marks near the drive belt check
hole are 5.0 mm (0.2 in) apart.

3. Note the position of the drive belt

with a force of 45 N (4.5 kgf, 10 lbf)
applied to the belt with a belt ten-
sion gauge as shown.

NOTE:

A belt tension gauge is available at a
Yamaha dealer.

4. Calculate the drive belt slack by

subtracting the measurement not-
ed in step 2 from the measurement
noted in step 3.

5. If the drive belt slack is incorrect,

have a Yamaha dealer adjust it.

1. Drive belt
2. Marks

3. Drive belt slack

1. Belt tension gauge

Drive belt slack:

7.5–13.0 mm (0.30–0.51 in)

chapter6 Page 20 Monday, October 24, 2005 1:31 PM

«
...
65
66
67
68
69
...
»

Содержание STRATOLINER XV19CTSV





































































































Отзывы:

Нет отзывов

Похожие инструкции для STRATOLINER XV19CTSV

Бренд: GLOBBER Страницы: 72

Бренд: Honda Страницы: 178

Бренд: GIVI Страницы: 3

Бренд: KEEWAY Страницы: 15

Бренд: Fantic Motor Страницы: 145

Venitex BARRIER

Бренд: DELTA PLUS Страницы: 2

Бренд: Ohlins Страницы: 2

Бренд: hepco & becker Страницы: 2

STAR XV19CSX(C)

Бренд: Yamaha Страницы: 96

Бренд: Yamaha Страницы: 102

Бренд: Yamaha Страницы: 100

Star XV250B 2011

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 248

Бренд: Yamaha Страницы: 86

Бренд: Caberg Страницы: 16

Бренд: hepco & becker Страницы: 3

Бренд: R&G Страницы: 6

Бренд: Shad Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды