background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-32

6

EAU23600

Replacing the fuses 

The main fuse and the signaling sys-
tem fuse holders are located under the
rider seat. (See page 3-8.)
If a fuse is blown, replace it as follows.

1. Turn the key to “OFF” and turn off

the electrical circuit in question.

2. Remove the blown fuse, and then

install a new fuse of the specified
amperage.

CAUTION:

ECA10640

Do not use a fuse of a higher amper-
age rating than recommended to
avoid causing extensive damage to
the electrical system and possibly a
fire.

3. Turn the key to “ON” and turn on

the electrical circuit in question to
check if the device operates.

4. If the fuse immediately blows

again, have a Yamaha dealer
check the electrical system.

EAU23780

Replacing the headlight bulb 

This model is equipped with a quartz
bulb headlight. If the headlight bulb
burns out, replace it as follows.

1. Remove the headlight unit by re-

moving the screws.

2. Disconnect the headlight coupler,

and then remove the bulb cover.

1. Main fuse

2. Spare main fuse

3. Signaling system fuse

Specified fuses:

Main fuse:

20.0 A

Signaling system fuse:

10.0 A

1. Screw

U2UJ1GE0.book  Page 32  Friday, May 11, 2007  10:23 AM

Содержание Star XV250X



































































































Отзывы: