Yamaha STAR XV19CSX Скачать руководство пользователя | Manualshive

Страница: 59 / 96

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-18

6

EAU22390

Checking the front and rear
brake pads

The front and rear brake pads must be
checked for wear at the intervals spec-
ified in the periodic maintenance and
lubrication chart.

EAU22430

Front brake pads

Each front brake pad is provided with
wear indicator grooves, which allow
you to check the brake pad wear with-
out having to disassemble the brake.
To check the brake pad wear, check
the wear indicator grooves. If a brake
pad has worn to the point that the wear

indicator grooves have almost disap-
peared, have a Yamaha dealer replace
the brake pads as a set.

EAU22500

Rear brake pads

Check each rear brake pad for damage
and measure the lining thickness. If a
brake pad is damaged or if the lining
thickness is less than 0.8 mm (0.03 in),
have a Yamaha dealer replace the
brake pads as a set.

EAU38630

Checking the brake and clutch
fluid levels

Front brake

Rear brake

1. Brake pad wear indicator groove

1. Lining thickness

1. Minimum level mark

1. Minimum level mark

U29S10E0.book Page 18 Friday, May 18, 2007 1:53 PM

«
...
57
58
59
60
61
...
»

Содержание STAR XV19CSX

































































































Отзывы:

Нет отзывов

Похожие инструкции для STAR XV19CSX

Бренд: LAZER Страницы: 13

Бренд: Fantic Motor Страницы: 130

Бренд: ICON Страницы: 8

Бренд: X-lite Страницы: 5

Apache RTR 160 HYPER EDGE 2015

Бренд: TVS Страницы: 60

Бренд: hepco & becker Страницы: 2

X-903 Ultra Carbon 29

Бренд: X-lite Страницы: 116

Бренд: Dakota Digital Страницы: 7

Бренд: METRAKIT Страницы: 53

Бренд: Spartus Страницы: 24

Бренд: hepco & becker Страницы: 7

Бренд: SHERCO Страницы: 102

Бренд: TVS Страницы: 48

Бренд: hepco & becker Страницы: 2

Бренд: R&G Страницы: 17

Бренд: R&G Страницы: 18

Бренд: R&G Страницы: 17

Бренд: Honda Страницы: 153

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды