Yamaha Star 2010 страница 31 Скачать руководство пользователя

Страница: 31 / 104

INSTRUMENT AND CONTROL FUNCTIONS

4-13

EAU42750

Rider seat

To remove the rider seat

1. Insert the key into the seat lock,

and then turn it counterclockwise.

2. Lift the front of the seat up, and

then pull the seat off.

To install the rider seat

1. Insert the projection on the rear of

the seat into the seat holder as
shown.

2. Push the front of the seat down to

lock it in place.

3. Remove the key.

TIP

Make sure that the seat is properly se-
cured before riding.

EAU14322

Helmet holder

The helmet holder is located under the
rider seat.

To secure a helmet to the helmet
holder

1. Remove the rider seat. (See page

4-13.)

2. Hook the helmet onto the helmet

holder, and then securely install
the seat.

WARNING! Never ride

with a helmet attached to the
helmet holder, since the helmet
may hit objects, causing loss of
control and possibly an acci-
dent.

[EWA10161]

1. Seat lock

2. Unlock.

1. Projection
2. Seat holder

1. Helmet holder

U5S614E0.book Page 13 Friday, July 9, 2010 9:18 AM

Содержание Star 2010









































































































Результаты поиска

Содержание Star 2010

Отзывы:

Похожие инструкции для Star 2010

Бренды по названию

Популярные бренды

Yamaha Star 2010, Руководство пользователя

Результаты поиска

Содержание Star 2010

Отзывы:

Похожие инструкции для Star 2010

Бренды по названию

Популярные бренды