Troubleshooting
Power does not turn on.
Did you firmly and securely connect the
power cord?
Power shuts down suddenly.
Are the vents of the mixer blocked?
Since inadequate ventilation can result in
overheating the mixer, the power may be
turned off automatically to protect from
overheating. Secure the ventilation for
cooling, then turn on the power again.
No sound is heard.
Did you connect the mixer’s SPEAKERS
jacks and the speakers’ input jacks
using the proper speaker cables?
Did you firmly and securely connect the
speaker cables?
Is a speaker other than the included
speaker (MODEL 600S) connected to
the mixer’s SPEAKERS jacks?
Please connect the included speaker
(MODEL 600S).
Did you use the included speaker
cables?
If you use a commercially-available
speaker cable with a metal-housing
connector, the cable will be shorted
when the connector touches other metal,
resulting in no sound being produced.
Is the POWER LED flashing at intervals?
There may be a short in the speaker cable
or the connection may be faulty. Check
that the speaker cable is not scratched
and is connected properly to the mixer,
then reapply the power.
For channels 7/8, are both phone and
RCA-pin jacks connected at the same
time? Or, for channels 9/10, are both
phone and stereo mini jacks connected
at the same time?
The phone jack has priority for channels
7/8 and the stereo mini jack has priority for
9/10.
Is the POWER LED flashing
continuously?
If the internal power amplifier section is
excessively overloaded, the amplifier will
be muted for protection. The mixer will
automatically reset itself after a while.
Sound is distorted or noise is
produced
Are the LEVEL controls of all relevant
channels and/or the MASTER LEVEL
control set too high?
Is the MIC/LINE switch of the
corresponding channel set to MIC?
If the input level from the source is high,
setting the MIC/LINE switch to MIC may
result in distorted sound. Set the switch to
LINE position.
Is the volume of the connected device
too high?
Lower the volume of the external device.
Is the speaker cable or the power cord
located near the input cables?
Please keep it away from the input cables.
Sound is not loud enough
Are the LEVEL controls of all relevant
channels and/or the MASTER LEVEL
control set too low?
Is the MIC/LINE switch of the
corresponding channel set to LINE?
Turn the LEVEL control to the minimum
(zero). Set the switch to the MIC position,
then slowly raise the LEVEL control.
Is the volume of the connected device
too low?
Raise the volume of the external device.
Is the PHANTOM switch set to on when
using a microphone that requires
phantom power?
The high sounds and low
sounds are unbalanced.
Are the equalizer controls raised or
lowered too much?
Set the equalizer controls to the center
position.
Is the speaker properly outputting the
high-frequency range signals?
If not, check the “Protective circuit (poly
switch)” note in the Notice section.
iPod/iPhone is not recognized
Is your iPod/iPhone charged?
If your iPod/iPhone has not been charged,
it may take some time to be recognized by
the mixer. Make sure that your iPod/iPhone
is connected to the mixer and wait until it is
sufficiently charged.
* If any specific problem should persist, please
contact your Yamaha dealer.
General Specifications
Maximum Output Power (SPEAKERS L/R)
340 W + 340 W/4 Ω @Dynamic at 1 kHz
280 W+280 W/4Ω @10 % THD at 1 kHz
230 W+230 W/4Ω @1 % THD at 1 kHz
Frequency Response
-3 dB, +1 dB @ 40 Hz-20 kHz, 1 W Output/4Ω
(without EQ and SP EQ) (SPEAKERS L/R)
-3 dB, +1 dB @ 40 Hz-20 kHz, +4 dBu 10 kΩ Load
(MONITOR OUT)
Total Harmonic Distortion
0.5 % @20 Hz-20 kHz, +11 dBu 10 kΩ (MONITOR OUT)
Hum & Noise (Rs= 150 Ω, MIC/LINE switch=MIC)
-113 dBu Equivalent input noise (CH1-4)
-58 dBu Residual output noise (SPEAKERS L/R)
Crosstalk (1 kHz)
-70 dB between input channels
Phantom Voltage
+30 V (CH1, 2)
Weight
25.4 kg (56 lbs) (Speaker 10.8 kg x 2 + Mixer 3.8 kg)
Package Contents
STAGEPAS 600i (includes two MODEL 600S Speakers
and a Powered Mixer), Cover Panel, Power Cord (2m),
two Speaker Cables (6m), 12 Non-Skid Pads, Owner’s
Manual (this booklet)
Power Consumption
35 W (Idle), 100 W (1/8 Power)
Power Requirement
100V - 240V 50Hz/60Hz
Input Channel Equalization
±15 dB
HIGH: 8 kHz shelving
MID: 2.5 kHz peaking
LOW: 100 Hz shelving
Supported iPod/iPhone models (as of August 2012)
iPod touch (1st, 2nd, 3rd, and 4th generation),
iPod classic, iPod nano (2nd, 3rd, 4th, 5th, and 6th
generation), iPhone 4S, iPhone 4, iPhone 3GS, iPhone
3G, iPhone
For updated information, check the Yamaha Pro Audio
website (http://www.yamahaproaudio.com/).
Speakers (MODEL 600S)
Enclosure
2 way bass-reflex type
Speaker Unit
LF: 10” (25 cm) Cone
HF: 1.4” (3.56 cm) Compression Driver
Crossover Frequency
2.8 kHz
Frequency Range
55 Hz-20 kHz (-10 dB)
Maximum Output Level
129 dB SPL (Measured peak IEC noise@1m)
Coverage Angle
90° (Horizontal)/60° (Vertical)
Block Diagram
Input Characteristics
Input Terminals
MIC/LINE
Input
Impedance
Source
Impedance
Input Level
Connector
Type
Sensitivity
Nominal
Max. before
Clipping
CH IN 1-2
XLR
MIC
3 kΩ
150 Ω Mics
-56 dBu
-35 dBu
-10 dBu
XLR-3-31
LINE
-30 dBu
-9 dBu
+16 dBu
CH IN 3-4
XLR
MIC
3 kΩ
150 Ω Mics
-56 dBu
-35 dBu
-10 dBu
XLR Combo
LINE
-30 dBu
-9 dBu
+16 dBu
Phone
MIC
10 kΩ
(Hi-Z 1 MΩ)
150 Ω Lines
(Hi-Z 10 kΩ)
-50 dBu
-29 dBu
-4 dBu
LINE
-24 dBu
-3 dBu
+22 dBu
CH IN 5/6
Phone
-
10 kΩ
150 Ω Lines
-24 dBu
-3 dBu
+22 dBu
Phone*
CH IN 7/8
Phone
-
10 kΩ
150 Ω Lines
-24 dBu
-3 dBu
+22 dBu
Phone*
Pin
-
10 kΩ
150 Ω Lines
-24 dBu
-3 dBu
+22 dBu
RCA Pin
CH IN 9/10
Phone
-
10 kΩ
150 Ω Lines
-24 dBu
-3 dBu
+22 dBu
Phone*
Mini
-
10 kΩ
150 Ω Lines
-24 dBu
-3 dBu
+22 dBu
Stereo Mini
Output Characteristics
Output Terminals
Output
Impedance
Load
Impedance
Output Level
Connector
Type
Nominal
Max. before
Clipping
Typ at
THD+N 10%
Dynamic
SPEAKERS OUT [L,R]
<0.1 Ω
4 Ω Speakers
62.5 W
230 W
280 W
340 W
Phone*
MONITOR OUT [L,R]
600 Ω
10 kΩ Lines
+4 dBu
+20 dBu
-
-
Phone*
SUBWOOFER OUT
150 Ω
10 kΩ Lines
-3 dBu
+17 dBu
-
-
Phone*
0 dBu=0.775 Vrms, 0 dBV=1 Vrms Phone*: Unbalanced
Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp.reserves the right to
change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may
not be the same in every locale, please check with your Yamaha dealer.
Dimensions
Mixer
Speaker
319
144
50°
354
109
96
2
135
335
545
348
197
Screw holes
for the Mic
Stand Adapter
BMS-10A
(optional)
Pole diameter 34.8 - 35.2
* Use of the stand should refer to stand
manufacturer’s instructions.
Attaching a speaker to a speaker stand
1
Attach the speaker to the speaker stand with the lock lever moved
up (release position).
Lock
lever
1
Release
2
Lock
2
Move the lock lever down to
lock to the stand.
INPUT
(CH1-2)
INPUT
(CH3)
INPUT
(CH7/8)
INPUT
(CH4)
INPUT
(CH5/6)
INPUT
(CH9/10)
[-56–+16dBu]
[-56–+16dBu]
[-50–+22dBu]
[-56–+16dBu]
[-50–+22dBu]
[-24–+22dBu]
[-24–+22dBu]
[-24–+22dBu]
COMBO
COMBO
PHANTOM (+30V)
MIC/LINE(-26dB)
HA
BA
EQ
MIC/LINE(-26dB)
L
R
REVERB
REVERB
REVERB
LEVEL
LOW
HIGH
LEVEL
M
ID
LOW
HIGH
MID
HA
BA
EQ
+
-
+
-
+
-
HA
BA
EQ
MIC/LINE(-26dB)
LOW
HIGH
MID
REVERB
LEVEL
SUM
SUM
SUM
AD
AD
AD
R
EVERB
L
R
REVERB
ON/OFF
FEEDBACK SU
PPRESSOR
MASTER
EQ
SP EQ (FI
XED)
LIMITER
MA
STER LEVEL
DA
DA
AMP
AMP
L
R
MASTER LEVEL
SPEAKERS OUT
(-1)
SUM
DA
DA
MONITOR OUT
SUBWOOFER OUT
(MONO)
MONITOR OUT
L(MONO)
R
BA
BA
REVERB ON/OFF
FOOT SWITCH
DSP
BA
BA
BA
BA
BA
BA
SUM
SUM
BA
BA
BA
BA
EQ
EQ
EQ
EQ
EQ
EQ
LO
W
HIGH
MID
LO
W
H
IG
H
M
ID
LO
W
H
IG
H
M
ID
LEVEL
LEVEL
LEVEL
ST/MONO
ST/MONO
ST/MONO
Hi-Z
Hi-Z(1MΩ)
L
L
R
R
R
L
L/R
DA
DA
USB
(iPod/iPhone)
USB
CONTROLLER
5V 1A
Specifications
Do not open
• This device contains no user-serviceable parts. Do not open the device
or attempt to disassemble the internal parts or modify them in any way.
If it should appear to be malfunctioning, discontinue use immediately
and have it inspected by qualified Yamaha service personnel.
Water warning
• Do not expose the device to rain, use it near water or in damp or wet
conditions, or place on it any containers (such as vases, bottles or
glasses) containing liquids which might spill into any openings. If
any liquid such as water seeps into the device, turn off the power
immediately and unplug the power cord from the AC outlet. Then have
the device inspected by qualified Yamaha service personnel.
• Never insert or remove an electric plug with wet hands.
Fire warning
• Do not put burning items, such as candles, on the unit. A burning item
may fall over and cause a fire.
If you notice any abnormality
• When one of the following problems occur, immediately turn off the
power switch and disconnect the electric plug from the outlet. Then
have the device inspected by Yamaha service personnel.
- The power cord or plug becomes frayed or damaged.
- It emits unusual smells or smoke.
- Some object has been dropped into the instrument.
- There is a sudden loss of sound during use of the device.
• If this mixer should be dropped or damaged, immediately turn off the
power switch, disconnect the electric plug from the outlet, and have the
device inspected by qualified Yamaha service personnel.
CAUTION
Always follow the basic precautions listed below
to avoid the possibility of physical injury to you or
others, or damage to the device or other property.
These precautions include, but are not limited to,
the following:
Power supply/Power cord
• When removing the electric plug from the device or an outlet, always
hold the plug itself and not the cord. Pulling by the cord can damage it.
• Remove the electric plug from the outlet when the device is not to be
used for extended periods of time, or during electrical storms.
Location
• Do not place the device in an unstable position. Unless the device is
securely affixed, do not install it in a location where it might fall, even if
the surface is level.
• Do not block the vents. This mixer has ventilation holes at the top
and sides to prevent the internal temperature from becoming too
high. In particular, do not place the mixer on its side or upside down.
Inadequate ventilation can result in overheating, possibly causing
damage to the mixer, or even fire.
• Do not use the device in a confined, poorly-ventilated location. Make
sure that there is adequate space between the mixer, or the speaker
fitted with the mixer, and surrounding walls or other devices: at
least 30cm at the sides, 30cm behind and 30cm above. Inadequate
ventilation can result in overheating, possibly causing damage to the
device(s), or even fire.
• If you lay the speaker flat on its side or like a stage monitor, make sure
to remove the mixer first.
• Do not hold the bottom of the speaker when transporting or moving it.
In doing so, you may pinch your hands under the speaker, and result in
injury.
• Do not place the device in a location where it may come into contact
with corrosive gases or salt air. Doing so may result in malfunction.
• Before moving the device, remove all connected cables.
• When setting up the mixer, make sure that the AC outlet you are using
is easily accessible. If some trouble or malfunction occurs, immediately
turn off the power switch and disconnect the plug from the outlet. Even
when the power switch is turned off, electricity is still flowing to the
product at the minimum level. When you are not using the product for a
long time, make sure to unplug the power cord from the wall AC outlet.
Connections
• Before connecting the device to other devices, turn off the power for
all devices. Before turning the power on or off for all devices, set all
volume levels to minimum.
• For the SPEAKERS jacks of the mixer, use only the included MODEL
600S speakers and speaker cables. Use of other types of speakers and
cables may result in damage, or even fire.
Maintenance
• Remove the power plug from the AC outlet when cleaning the device.
Handling caution
• Do not insert your fingers or hands in any gaps or openings on the
vents or panel of the mixer and the ports of the speaker.
• Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.)
into any gaps or openings on the vents or panel of the mixer and the
ports of the speaker. If this happens, turn off the power immediately
and unplug the power cord from the AC outlet. Then have the device
inspected by qualified Yamaha service personnel.
• Do not rest your weight on the device or place heavy objects on it, and
avoid use excessive force on the buttons, switches or connectors.
• Do not use the speakers for a long period of time at a high or
uncomfortable volume level, since this can cause permanent hearing
loss. If you experience any hearing loss or ringing in the ears, consult a
physician.
• Do not operate the device if the sound is distorting. Prolonged use in
this condition could cause overheating and result in fire.
• Do not pull on any attached cable, such that of a microphone. Doing so
may cause the speaker to topple, and result in damage or in injury.
Yamaha cannot be held responsible for damage caused by improper
use or modifications to the device, or data that is lost or destroyed.
PA_en_1
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
* Please keep this manual in a safe place for future reference.
Notice
To avoid the possibility of malfunction or damage to the product, follow
the notices below.
Handling and Maintenance
• Do not expose the device to excessive dust or vibration, or extreme cold
or heat (such as in direct sunlight, near a heater, or in a car during the
day), in order to prevent the possibility of panel disfiguration, unstable
operation, or damage to the internal components.
• Do not place vinyl, plastic or rubber objects on the device, since this
might discolor the panel.
• When cleaning the device, use a dry and soft cloth. Do not use paint
thinners, solvents, cleaning fluids, or chemical-impregnated wiping
cloths.
• Condensation can occur in the device due to rapid, drastic changes in
ambient temperature—when the device is moved from one location
to another, or air conditioning is turned on or off, for example. Using
the device while condensation is present can cause damage. If there
is reason to believe that condensation might have occurred, leave
the device for several hours without turning on the power until the
condensation has completely dried out.
• Avoid setting all equalizer controls and LEVEL knobs to their maximum.
Depending on the condition of the connected devices, doing so may
cause feedback and may damage the speakers.
• When turning on the AC power in your audio system, always turn on
the mixer LAST, to avoid speaker damage due to the noise. When
turning the power off, the mixer should be turned off FIRST for the same
reason.
•
Protective circuit (poly switch)
All full-range loudspeakers are fitted with a self-resetting poly switch
that protects the high-frequency driver from damage caused by
excessive power. If a loudspeaker cabinet loses high-frequency output,
immediately remove power from the unit and wait for two to three
minutes. This should be long enough to allow the poly switch to reset.
Reapply power and check the performance of the highfrequency driver
before continuing, with the power reduced to a level that does not cause
the poly switch to interrupt the signal.
•
Interference from cell phones
Using a cell phone near the speaker system can induce noise. If this
occurs, move the cell phone further away from the speaker system.
• Air blowing out of the bass reflex ports is normal, and often occurs
when the speaker is handling program material with heavy bass
content.
• Always turn the power off when the device is not in use.
Connectors
• XLR-type connectors are wired as follows (IEC60268 standard): pin 1:
ground, pin 2: hot (+), and pin 3: cold (-).
Information
About functions/data bundled with the device
• iPod
TM
, iPhone
TM
iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks
of Apple Inc., registered in the U.S. and other countries.
“Made for iPod” and “Made for iPhone” mean that an electronic
accessory has been designed to connect specifically to iPod or iPhone
respectively, and has been certified by the developer to meet Apple
performance standards. Apple is not responsible for the operation of
this device or its compliance with safety and regulatory standards.
Please note that the use of this accessory with iPod or iPhone may
affect wireless performance.
About this manual
• The illustrations as shown in this manual are for instructional purposes
only, and may appear somewhat different from those on your device.
• The company names and product names in this manual are the
trademarks or registered trademarks of their respective companies.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The above warning is located on the bottom of the mixer.
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing) instructions
in the literature accompanying the product.
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade or the third
prong are provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods
of time.
14. Refer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally,
or has been dropped.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
(UL60065_03)
FCC INFORMATION (U.S.A.)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this
manual, meets FCC requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to use the product.
2. IMPORTANT:
When connecting this product to accessories and/or another
product use only high quality shielded cables. Cable/s supplied with this
product MUST be used. Follow all installation instructions. Failure to follow
instructions could void your FCC authorization to use this product in the USA.
3. NOTE:
This product has been tested and found to comply with the
requirements listed in FCC Regulations, Part 15 for Class “B” digital
devices. Compliance with these requirements provides a reasonable level of
assurance that your use of this product in a residential environment will not
result in harmful interference with other electronic devices. This equipment
generates/uses radio frequencies and, if not installed and used according to
the instructions found in the users manual, may cause interference harmful to
the operation of other electronic devices. Compliance with FCC regulations
does not guarantee that interference will not occur in all installations. If this
product is found to be the source of interference, which can be determined by
turning the unit “OFF” and “ON”, please try to eliminate the problem by using
one of the following measures:
Relocate either this product or the device that is being affected by the
interference.
Utilize power outlets that are on different branch (circuit breaker or fuse)
circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the antenna. If the
antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-axial type
cable.
If these corrective measures do not produce satisfactory results, please contact
the local retailer authorized to distribute this type of product. If you can not
locate the appropriate retailer, please contact Yamaha Corporation of America,
Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA90620
The above statements apply ONLY to those products distributed by Yamaha
Corporation of America or its subsidiaries.
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.
(class B)
C.S.G., Pro Audio Division
©2012 Yamaha Corporation
208MWHD*.*-01A0
Printed in China
WARNING
Always follow the basic precautions listed below to
avoid the possibility of serious injury or even death
from electrical shock, short-circuiting, damages,
fire or other hazards. These precautions include, but
are not limited to, the following:
Power supply/Power cord
• Do not place the power cord near heat sources such as heaters or
radiators, and do not excessively bend or otherwise damage the cord,
place heavy objects on it, or place it in a position where anyone could
walk on, trip over, or roll anything over it.
• Only use the voltage specified as correct for the mixer. The required
voltage is printed on the name plate of the mixer.
• Use only the supplied power cord.
If you intend to use the device in an area other than in the one you
purchased, the included power cord may not be compatible. Please
check with your Yamaha dealer.
• Check the electric plug periodically and remove any dirt or dust which
may have accumulated on it.
• Be sure to connect to an appropriate outlet with a protective grounding
connection. Improper grounding can result in electrical shock.
Information for Users on Collection and Disposal of
Old Equipment
This symbol on the products, packaging, and/or accompanying
documents means that used electrical and electronic products
should not be mixed with general household waste.
For proper treatment, recovery and recycling of old products,
please take them to applicable collection points, in accordance
with your national legislation and the Directives 2002/96/EC.
By disposing of these products correctly, you will help to save valuable resources
and prevent any potential negative effects on human health and the environment
which could otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old products, please contact
your local municipality, your waste disposal service or the point of sale where you
purchased the items.
[For business users in the European Union]
If you wish to discard electrical and electronic equipment, please contact your dealer
or supplier for further information.
[Information on Disposal in other Countries outside the European Union]
This symbol is only valid in the European Union. If you wish to discard these items,
please contact your local authorities or dealer and ask for the correct method of disposal.
(weee_eu)
IMPORTANT NOTICE FOR THE UNITED
KINGDOM
Connecting the Plug and Cord
WARNING:
THIS APPARATUS MUST BE EARTHED IMPORTANT. The wires
in this mains lead are coloured in accordance with the following code:
GREEN-AND-YELLOW : EARTH
BLUE
: NEUTRAL
BROWN
: LIVE
As the colours of the wires in the mains lead of this apparatus may not
correspond with the coloured markings identifying the terminals in your plug
proceed as follows:
The wire which is coloured GREEN-and-YELLOW must be connected to the
terminal in the plug which is marked by the letter E or by the safety earth
symbol
or colored GREEN or GREEN-and-YELLOW.
The wire which is coloured BLUE must be connected to the terminal which is
marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which
is marked with the letter L or coloured RED.
(3 wires)
이
기기는
가정용
(B
급
)
전자파적합기기로서
주로
가정에서
사용하는
것을
목적으로
하며
,
모든
지역에서
사용할
수
있습니다
.
(class b korea)
In Finland: Laite on liitettävä suojamaadoituskoskettimilla varustettuun
pistorasiaan.
In Norway: Apparatet må tilkoples jordet stikkontakt.
In Sweden: Apparaten skall anslutas till jordat uttag.
(class I hokuo)
For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below.
Yamaha Pro Audio global web site
http://www.yamahaproaudio.com/
Yamaha Manual Library
http://www.yamaha.co.jp/manual/
Unit: mm
