Yamaha SP02R96, Руководство по обслуживанию

Страница: 135 / 382

135
02R96
d. Start up the application to be used for writing
data into the computer.
e. Select the I/O port.
f. Open the data file to be loaded (02r96.bin) and
execute the loading procedure.
g. 02R96 will automatically restart a few moments
after loading has been completed.
h. End the application.
i. Press channels 5,9,6 and 3 in that order with
the channel [SEL] key, and then press the
[ENTER] key. Check to ascertain that the [MAIN]
version number displayed on the LCD screen
is the same as the installed program version.
j. Switch off the power to 02R96.
k. Press down simultaneously on the AUX
SELECT [DISPLAY] key and the [AUX1] key and
then switch on the power to start up the system.
Check to ascertain that the DIO WORD CLOCK
SELECT screen is displayed.
For the latest main program, please download from the
YSISS home page.
1-5. How to check the sub program version
If the sub program version is not the latest one,
then it is necessary to upgrade to the most recent
version.
Switch on the power to the main unit and check to
ascertain that it has started up. Use the channel
[SEL] key to press channels 5, 9, 6 and 3 in that
order, and then press the [ENTER] key to display
the required information. It is necessary for both
SUB1 and SUB2 to be the latest versions.
1-6. Fader sensing inspections
q
Preparations
a. Set the layer to “MASTER”, click on the “OUT
FADER” tab on the group screen, and then
perform grouping for the CH9 to 24 and
STEREO faders with the use of the [SEL] key
with all of the faders between CH9 and 24 and
STEREO set at the maximum values.
b. Set the layer to “1 - 24”, click on the “FADER 1 -
48” tab on the group screen, and then perform
grouping for the CH1 to 10 faders with the use
of the [SEL] key with all of the faders between
CH1 and 10 set at the maximum values.
w
Special learning
a. Set the layer to “MASTER”, operate the CH9
fader to divide all 100mm strokes into equal
units of 10, and then move then approximately
10mm. When they have been moved once, they
will be stopped for 0.5 seconds or longer.
(Lear ning is achieved throughout these
positioning operations.)
b. Perform the operations outlined in ‘a’ above for
all positions from MAX to MIN.
c. Then perform the operations outlined in ‘a’ above
for all positions from MIN to MAX.
d. Set the layer to “1 - 24”, operate the CH10 fader
to divide all 100mm strokes into equal units of
10, and then move then approximately 10mm.
When they have been moved once, they will be
stopped for 0.5 seconds or longer. (Learning is
achieved throughout these positioning
operations.)
e. Perform the operations outlined in ‘d’ above for
all positions from MAX to MIN.
f. Then perform the operations outlined in ‘d’ above
for all positions from MIN to MAX.
e
Group sensing inspections
a. Set the layer to “MASTER”, and then operate
the CH9 fader for two slow return trips and two
fast return trips.
b. Set the layer to “1 - 24”, and then operate the
CH10 fader for two slow return trips and two
fast return trips.
c. While performing the above procedures, check
to confirm that there are no faders that vibrate
or that are exceptionally slow.
r
Recall sensing inspections
a. Select “1 - 24” for the layer, and then recall No.0.
b. Set all faders to the MAX position, and store
them in No.1.
c. After recalling No.0, recall No.1.
d. Repeat procedure ‘c’ twice.
e. While performing the above procedures, check
to confirm that there are no faders that vibrate
or that are exceptionally slow.