Yamaha RX10RTW Скачать руководство пользователя страница 79

Страница: 79 / 100

8-29

Adjusting the drive track

WARNING

●

Be sure to have a Yamaha dealer make this
adjustment.

●

Support the snowmobile securely on a suitable
stand before working underneath the snowmo-
bile.

●

Operate the engine in a well-ventilated area.

1. Lift the rear of the snowmobile onto a suitable stand

to raise the drive track off the ground.

2. Loosen the rear axle nut

3. Start the engine and rotate the drive track one or two

turns. Stop the engine.

4. Check the drive track alignment with the slide

runners

. If the alignment is incorrect, align the

drive track by turning the left and right adjusters.

CD-08E

Slide runners

Drive track

Slide metal

Gap

Forward

5. Adjust the drive track deflection to specification.

CD-09E

Drive track

alignment

Shifted to right

Shifted to left

Left adjuster

Turn out

Turn in

Right adjuster

Turn in

Turn out

Drive track

deflection

More than

specified

Less than

specified

Left adjuster

Turn in

Turn out

Right adjuster

Turn in

Turn out

E_8gt.book Page 29 Tuesday, March 28, 2006 5:37 PM

Содержание RX10RTW





































































































Результаты поиска

Содержание RX10RTW

Отзывы:

Похожие инструкции для RX10RTW

Бренды по названию

Популярные бренды

Yamaha RX10RTW, Руководство пользователя

Результаты поиска

Содержание RX10RTW

Отзывы:

Похожие инструкции для RX10RTW

Бренды по названию

Популярные бренды