background image

31

REMOTE CONTROL TRANSMITTER

Battery installation

1

2

3

Battery replacement

If you find that the remote control transmitter must be
used closer to the main unit, the batteries are weak.
Replace both batteries with new ones.

Notes:

• Use only AA, LR6, UM-3 batteries for replacement.
• Be sure the polarities are correct. (See the illustration

inside the battery compartment.)

• Remove the batteries if the remote control transmitter

will not be used for an extended period of time.

• If batteries leak, dispose of them immediately. Avoid

touching the leaked material or letting it come in contact
with clothing, etc. Clean the battery compartment
thoroughly before installing new batteries.

Remote control transmitter operation range

Remoto control 
sensor

30°

30°

Within approximately 
7 m (23 feet)

Notes:

• There should be no large obstacles between the remote

control transmitter and the main unit.

• If the remote control sensor is directly illuminated by

strong lighting (especially an inverter type of fluorescent
lamp etc.), it might cause the remote control transmitter
not to work correctly. In this case, reposition the main
unit to avoid direct lighting.

STANDBY mode (Singapore model only)

While the power is on, pressing the POWER key on
the remote control transmiter switches the unit to the
STANDBY mode. (In this mode, the indicator is half
illuminated.)

POWER on mode

STANDBY mode

Содержание RX-V890








































Отзывы: