background image

TI CH INPUT

HDMI 2

HDMI 3

HDMI 4

HDMI 5

SUBWOOFER

SUR.BACK

ND

GER OUT

+12V

0.1A MAX.

CENTER

MOTE

AUDIO

OUT

ZONE2

OUT

SURROUND

SUR.BACK

PRE OUT

SUBWOOFER

1

2

FRONT

CENTER

SINGLE

SPEAKERS

CENTER

SURROUND

SURROUND BACK/

BI-AMP

SINGLE

FRONT

TI CH INPUT

HDMI 2

HDMI 3

HDMI 4

HDMI 5

SUBWOOFER

SUR.BACK

ND

GER OUT

+12V

0.1A MAX.

CENTER

MOTE

AUDIO

OUT

ZONE2

OUT

SURROUND

SUR.BACK

PRE OUT

OOFER 2

FRONT

CENTER

SINGLE

6.1

7.1

7.1

- 3 -

1

1

 

Connect the speakers

Front speaker

R                  L

Surround back

speaker
R         L

Surround 

speaker
R         L

Subwoofer

Center speaker

Connecting speakers

Connecting the subwoofer

1

 

Connect the subwoofer input jack to the SUBWOOFER 
1 or 2 jack on this unit with an audio pin cable. 

SURR

OUND

 BAC

K/

BI-AMP

•  When connecting the presence speakers, refer to “Presence speaker 

connection” in the Owner’s Manual.

•  This unit can connect speakers that support Bi-amp connection for front 

speakers. Refer to “Bi-amp connection” in the Owner’s Manual for the 
details.

7.1

 Connect when using with 7.1-channel speaker layout.

6.1

 Connect when using with 6.1-channel speaker layout.

FR

ONT

2

2

3

1

4

4

1

 

Remove approximately 10 mm of insulation from 
the ends of the speaker cables, and twist the bare 
wires of the cables together fi rmly so that they will 
not cause short circuits.

2

 

Loosen the speaker terminals.

3

 

Insert the bare wire of the speaker cable into the 
gap on the side of the terminal.

4

 

Tighten the terminal. 

2

 

Set the subwoofer volume as follows.

Volume: Set to approximately half volume (or slightly less than half). 
Crossover frequency (if available): Set to maximum.

Subwoofer examples

VOLUME

MIN

MAX

CROSSOVER/

HIGH CUT

MIN

MAX

Caution:

•  Remove the AC power cable of this unit from the power outlet 

before connecting the speakers. 

•  Generally speaker cables consist of two parallel insulated 

cables. One of these cables is a different color, or has a line 
running along it, to indicate different polarity. Insert the different 
colored (or lined) cable into the “+” (positive, red) terminal 
on this unit and the speakers, and the other cable into the “-” 
(minus, black) terminal. 

•  Be careful that the core of the speaker cable does not touch 

anything or come into contact with the metal areas of this unit. 
This may damage this unit or the speakers. If the speaker cables 
short circuit, “CHECK SP WIRES!” will appear on the front panel 
display when this unit is switched on. 

•  This unit is confi gured for 8Ω speakers at the factory setting. 

When connecting 6Ω speakers, confi gure the speaker impedance 
setting of this unit to 6Ω. When this unit is confi gured for 6Ω 
speakers, 4Ω speakers can also be used as the front speakers. 
For more information on setting the speaker impedance, refer to 
“Changing speaker impedance” in the Owner’s Manual.

Connecting the banana plug

Tighten the knob, and then insert the banana plug 
into the end of the terminal.

Banana plug

FR

ON

T

Содержание RX-V667









Отзывы: