Yamaha RX 497 - AV Receiver Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 53

background image

EXAMPLE OF ANTENNA GROUNDING

MAST

GROUND
CLAMP

ANTENNA
LEAD IN
WIRE

ANTENNA
DISCHARGE UNIT
(NEC SECTION 810–20)

GROUNDING CONDUCTORS
(NEC SECTION 810–21)

GROUND CLAMPS

POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PART H)

ELECTRIC
SERVICE
EQUIPMENT

NEC

– NATIONAL ELECTRICAL CODE

20

Replacement Parts – When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer or have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other
hazards.

21

Safety Check – Upon completion of any service or repairs to
this product, ask the service technician to perform safety
checks to determine that the product is in proper operating
condition.

22

Wall or Ceiling Mounting – The unit should be mounted to a
wall or ceiling only as recommended by the manufacturer.

23

Heat – The product should be situated away from heat
sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.

24

Outdoor Antenna Grounding – If an outside antenna or
cable system is connected to the product, be sure the antenna
or cable system is grounded so as to provide some
protection against voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSI/NFPA 70,
provides information with regard to proper grounding of the
mast and supporting structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.

WG63450

Printed in Malaysia

a

RX-497_397_U_FLR.fm Page ii Thursday, September 8, 2005 9:51 AM

«
...
51
52
53

Содержание RX 497 - AV Receiver






















































Отзывы:

Нет отзывов

Похожие инструкции для RX 497 - AV Receiver

Бренд: Neo Car Audio Страницы: 16

Бренд: 2N Страницы: 23

Бренд: QFX Страницы: 2

Бренд: GRAUPNER Страницы: 52

Бренд: Ignition Страницы: 9

Бренд: Boss Audio Systems Страницы: 17

VM9412 - In-dash DVD Receiver

Бренд: Jensen Страницы: 38

Бренд: Sennheiser Страницы: 2

Бренд: Cobolt Страницы: 5

Бренд: Olin Страницы: 26

Бренд: Milennia Страницы: 8

Бренд: Dat Viet Страницы: 18

Бренд: Precision Power Страницы: 19

Бренд: Sangean Страницы: 12

Бренд: FOUR Страницы: 28

Бренд: Kraken Acoustics Страницы: 12

Бренд: Rotel Страницы: 15

Бренд: PCB Piezotronics Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды