Yamaha RS90L Скачать руководство пользователя страница 65

Страница: 65 / 92

8-17

3. Remove the dipstick and check that the oil is between

the maximum and minimum level marks. If the oil is
below the minimum level mark, add sufficient oil to
raise it to the maximum level mark.

Maximum level mark

Minimum level mark

For models without reverse transmissions (RS90)

For models with reverse transmissions
(not applicable)

CAUTION:

Make sure that no foreign material enters the drive
chain housing.

4. Install the dipstick, making sure to align the notch

in the dipstick handle with the projection

on the

drive chain housing.

Adjusting the chain tension

1. Loosen the locknut.
2. Turn the adjusting bolt clockwise until it is finger tight,

and then loosen it 1/4 turn.

3. Hold the adjusting bolt in place while tightening the

locknut.

Locknut

Adjusting bolt

Drive chain oil: GL-3

75W or 80W

E_8es.book Page 17 Saturday, August 6, 2005 8:47 AM

Содержание RS90L





























































































Результаты поиска

Содержание RS90L

Отзывы:

Похожие инструкции для RS90L

Бренды по названию

Популярные бренды

Yamaha RS90L, Руководство пользователя

Результаты поиска

Содержание RS90L

Отзывы:

Похожие инструкции для RS90L

Бренды по названию

Популярные бренды