Yamaha RoadStan XV17AMC Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 107

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-21

6

NOTE:

These limits may be different by regula-
tion from country to country. If so, con-
form to the limits specified by the
regulations of your own country.

WARNING

EWA10580

●

It is dangerous to ride with a
worn-out tire. When a tire tread
begins to show crosswise lines,
have a Yamaha dealer replace
the tire immediately.

●

The replacement of all wheel-
and brake-related parts, includ-
ing the tires, should be left to a
Yamaha dealer, who has the
necessary professional knowl-
edge and experience.

EAU21940

Spoke wheels

To maximize the performance, durabil-
ity, and safe operation of your motor-
cycle, note the following points
regarding the specified wheels.

●

The wheel rims should be checked
for cracks, bends or warpage, and
the spokes for looseness or dam-
age before each ride. If any dam-
age is found, have a Yamaha
dealer replace the wheel. Do not
attempt even the smallest repair to
the wheel. A deformed or cracked
wheel must be replaced.

●

The wheel should be balanced
whenever either the tire or wheel
has been changed or replaced. An
unbalanced wheel can result in
poor performance, adverse han-
dling characteristics, and a short-
ened tire life.

●

Ride at moderate speeds after
changing a tire since the tire sur-
face must first be “broken in” for it
to develop its optimal characteris-
tics.

EAU21960

Cast wheels

To maximize the performance, durabil-
ity, and safe operation of your vehicle,
note the following points regarding the
specified wheels.

●

The wheel rims should be checked
for cracks, bends or warpage be-
fore each ride. If any damage is
found, have a Yamaha dealer re-
place the wheel. Do not attempt
even the smallest repair to the
wheel. A deformed or cracked
wheel must be replaced.

●

The wheel should be balanced
whenever either the tire or wheel
has been changed or replaced. An
unbalanced wheel can result in
poor performance, adverse han-
dling characteristics, and a short-
ened tire life.

●

Ride at moderate speeds after
changing a tire since the tire sur-
face must first be “broken in” for it
to develop its optimal characteris-
tics.

U5VN13E0.book Page 21 Monday, May 15, 2006 2:13 PM

«
...
65
66
67
68
69
...
»

Содержание RoadStan XV17AMC












































































































Отзывы:

Нет отзывов

Похожие инструкции для RoadStan XV17AMC

Бренд: Dakota Digital Страницы: 6

Бренд: Öhlins Страницы: 8

Бренд: Öhlins Страницы: 8

prodrive SUR 3A00

Бренд: Öhlins Страницы: 4

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 8

Бренд: Öhlins Страницы: 4

Бренд: KTM Power Parts Страницы: 7

Бренд: Saddlemen Страницы: 3

Бренд: R&G Страницы: 6

Бренд: hepco & becker Страницы: 3

Бренд: X-lite Страницы: 96

Бренд: hepco & becker Страницы: 3

Бренд: DYNATEK Страницы: 3

Бренд: DYNATEK Страницы: 8

Бренд: LSL Страницы: 4

VENTURA BIKE-PACK SYSTEM Series

Бренд: DOLD Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды