Yamaha R1 Series 2015 Скачать руководство пользователя страница 671

Страница: 671 / 704

ELECTRICAL COMPONENTS

8-190

EAS30574

CHECKING THE FUEL LEVEL WARNING

LIGHT

This model is equipped with a self-diagnosis de-
vice for the fuel level detection circuit.
1. Check:

•

Fuel level warning light “1”
(Turn the main switch to “ON”.)
Warning light comes on for a few seconds,
then goes off

Warning light is OK.

Warning light does not come on

Replace

the meter assembly.
Warning light flashes eight times, then goes
off for 3 seconds in a repeated cycle (mal-
function detected in fuel sender)

Replace

the fuel pump assembly.

EAS30577

CHECKING THE RADIATOR FAN MOTORS

1. Check:

•

Radiator fan motor
Faulty/rough movement

Replace.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Disconnect the radiator fan motor coupler

from the wire harness.

b. Connect the battery (DC 12 V) as shown.

c. Measure the radiator fan motor movement.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS30578

CHECKING THE COOLANT TEMPERATURE

SENSOR

1. Remove:

•

Coolant temperature sensor
Refer to “CYLINDER HEAD” on page 5-23.

WARNING

EWA14130

• Handle the coolant temperature sensor

with special care.

• Never subject the coolant temperature sen-

sor to strong shocks. If the coolant temper-

ature sensor is dropped, replace it.

2. Check:

•

Coolant temperature sensor resistance
Out of specification

Replace.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Connect the pocket tester (

1 k/

100)

to the coolant temperature sensor as shown.

b. Immerse the coolant temperature sensor “1”

in a container filled with coolant “2”.

TIP

Make sure the coolant temperature sensor ter-
minals do not get wet.

c. Place a thermometer “3” in the coolant.

•

Positive tester probe

blue “1”

•

Negative tester probe

black “2”

ODO

FUEL CON

--.-

km/h

1000 r/min

MODE-

PWR

TCS

SCS

A-1

LCS

LIF

GPS

12:00

Coolant temperature sensor re-

sistance

2517–2777

@20

C (68

Coolant temperature sensor re-

sistance

210–221

@100

C (212

Pocket tester

90890-03112

Analog pocket tester

YU-03112-C

Содержание R1 Series 2015

































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание R1 Series 2015

Отзывы:

Похожие инструкции для R1 Series 2015

Бренды по названию

Популярные бренды

Yamaha R1 Series 2015, Руководство по обслуживанию

Результаты поиска

Содержание R1 Series 2015

Отзывы:

Похожие инструкции для R1 Series 2015

Бренды по названию

Популярные бренды