Yamaha R1 Series 2015 Скачать руководство пользователя страница 285 | Manualshive

Страница: 285 / 704

background image

ABS (Anti-lock Brake System)

4-68

EAS30197

REMOVING THE HYDRAULIC UNIT

ASSEMBLY

NOTICE

ECA18230

Unless necessary, avoid removing and in-

stalling the brake pipes of the hydraulic unit

assembly.

WARNING

EWA13930

Refill with the same type of brake fluid that is

already in the system. Mixing fluids may re-

sult in a harmful chemical reaction, leading

to poor braking performance.

NOTICE

ECA19790

• Handle the ABS components with care

since they have been accurately adjusted.

Keep them away from dirt and do not sub-

ject them to shocks.

• Do not set the main switch to “ON” when

removing the hydraulic unit assembly.

• Do not clean with compressed air.

• Do not reuse the brake fluid.

• Brake fluid may damage painted surfaces

and plastic parts. Therefore, always clean

up any spilt brake fluid immediately.

• Do not allow any brake fluid to contact the

couplers. Brake fluid may damage the cou-

plers and cause bad contacts.

• If the brake pipe flare nuts for the hydraulic

unit assembly have been removed, be sure

to tighten them to the specified torque and

bleed the brake system.

1. Disconnect:

•

ABS ECU coupler “1”

TIP

While pushing the portion “a” of the ABS ECU
coupler, pull the lock lever up to release the lock.

NOTICE

ECA20080

Do not use a tool to disconnect the ABS ECU

coupler.

2. Remove:

•

Brake hoses

•

Brake pipes

TIP

•

Do not operate the brake lever and brake pedal
while removing the brake hoses and brake
pipes.

•

Do not bend the brake pipe when loosening the
brake pipe flare nuts.

NOTICE

ECA19800

• When removing the brake hoses and brake

pipes, cover the area around the hydraulic

unit assembly to catch any spilt brake fluid.

Do not allow the brake fluid to contact other

parts.

• Before disconnecting the brake pipes from

the hydraulic unit assembly, do not lift up

or move the brake pipes.

3. Remove:

•

Hydraulic unit assembly “1”

TIP

To avoid brake fluid leakage and to prevent for-
eign materials from entering the hydraulic unit
assembly, insert a rubber plug “a” or a bolt (M10

u

1.00) into each flare nut hole.

NOTICE

ECA19810

When using a bolt, do not tighten the bolt un-

til the bolt head touches the hydraulic unit.

Otherwise, the brake pipe seating surface

could be deformed.

1

a

«
...
283
284
285
286
287
...
»

Содержание R1 Series 2015

































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для R1 Series 2015

Бренд: Can-Am Страницы: 16

Бренд: Can-Am Страницы: 254

B-TRK502-02-01-SL

Бренд: SRC Страницы: 4

Бренд: hepco & becker Страницы: 5

Бренд: Memphis Shades Страницы: 2

Бренд: TB Страницы: 8

Бренд: Caberg Страницы: 16

Бренд: R&G Страницы: 4

Бренд: Honda Страницы: 150

Бренд: hepco & becker Страницы: 6

Бренд: Yamaha Страницы: 108

Бренд: Yamaha Страницы: 100

Бренд: VESPA Страницы: 25

SENDA R/SM 125 4T Baja

Бренд: Derbi Страницы: 124

Бренд: Can-Am Страницы: 172

Бренд: Can-Am Страницы: 195

Krauser 610.092 00 02

Бренд: Wunderlich Страницы: 4

Бренд: hepco & becker Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды