Yamaha R1 Series 2015 Скачать руководство пользователя страница 276

Страница: 276 / 704

REAR BRAKE

4-59

EAS30183

INTRODUCTION

WARNING

EWA14101

Disc brake components rarely require disas-

sembly. Therefore, always follow these pre-

ventive measures:

• Never disassemble brake components un-

less absolutely necessary.

• If any connection on the hydraulic brake

system is disconnected, the entire brake

system must be disassembled, drained,

cleaned, properly filled, and bled after reas-

sembly.

• Never use solvents on internal brake com-

ponents.

• Use only clean or new brake fluid for clean-

ing brake components.

• Brake fluid may damage painted surfaces

and plastic parts. Therefore, always clean

up any spilt brake fluid immediately.

• Avoid brake fluid coming into contact with

the eyes as it can cause serious injury.

FIRST AID FOR BRAKE FLUID ENTERING

THE EYES:

• Flush with water for 15 minutes and get im-

mediate medical attention.

EAS30184

CHECKING THE REAR BRAKE DISC

1. Remove:

•

Rear wheel
Refer to “REAR WHEEL” on page 4-34.

2. Check:

•

Rear brake disc
Damage/galling

Replace.

3. Measure:

•

Brake disc runout
Out of specification

Correct the brake disc

runout or replace the brake disc.
Refer to “CHECKING THE FRONT BRAKE
DISCS” on page 4-48.

4. Measure:

•

Brake disc thickness
Measure the brake disc thickness at a few dif-
ferent locations.
Out of specification

Replace.

Refer to “CHECKING THE FRONT BRAKE
DISCS” on page 4-48.

5. Adjust:

•

Brake disc runout
Refer to “CHECKING THE FRONT BRAKE
DISCS” on page 4-48.

6. Install:

•

Rear wheel
Refer to “REAR WHEEL” on page 4-34.

EAS30185

REPLACING THE REAR BRAKE PADS

TIP

When replacing the brake pads, it is not neces-
sary to disconnect the brake hose or disassem-
ble the brake caliper.

1. Measure:

•

Brake pad wear limit “a”
Out of specification

Replace the brake

pads as a set.

2. Install:

•

Brake pad insulators

•

Brake pad shims
(onto the brake pads)

•

Brake pad spring
(into the rear brake caliper)

•

Brake pads

Brake disc runout limit (as mea-

sured on wheel)

0.15 mm (0.0059 in)

Brake disc thickness limit

4.5 mm (0.18 in)

Rear brake disc bolt

30 Nm (3.0 m·kgf, 22 ft·lbf)

LOCTITE®

Brake pad lining thickness (inner)

4.5 mm (0.18 in)

Limit

1.0 mm (0.04 in)

Brake pad lining thickness (outer)

4.5 mm (0.18 in)

Limit

1.0 mm (0.04 in)

Содержание R1 Series 2015

































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание R1 Series 2015

Отзывы:

Похожие инструкции для R1 Series 2015

Бренды по названию

Популярные бренды

Yamaha R1 Series 2015, Руководство по обслуживанию

Результаты поиска

Содержание R1 Series 2015

Отзывы:

Похожие инструкции для R1 Series 2015

Бренды по названию

Популярные бренды