Yamaha QY700, Справочник

Страница: 35 / 43

First transmit an RPN MSB and RPN LSB to specify the parameter that is to be
controlled. Then use Data Entry to set the value of the specified parameter.
RPN D.ENTRY
LSB MSB MSB LSB PARAMETER NAME DATA RANGE
00H 00H mmH --- PITCH BEND SENSITIVITY 00H - 18H (0-24 semitones)
01H 00H mmH llH MASTER FINE TUNE {mmH,llH} = {00H,00H} - {40H,00H} -
{7FH,7FH}(-8192*100/8192) - 0 - (+8192
*100/8192)
02H 00H mmH --- MASTER COARSE TUNE 28H - 40H - 58H (-24-0-+24 semitones)
7FH 7FH --- --- RPN RESET Set to a condition in which RPN number is
unspecified. Internal settings will not
change.
(3-4) NON-REGISTERED PARAMETER NUMBER
STATUS 1011nnnn(BnH) n = 0 ‘ 15 VOICE CHANNEL NUMBER
LSB 01100010(62H)
RPN LSB 0ppppppp p = NRPN LSB irefer to table below j
MSB 01100011(63H)
RPN MSB 0qqqqqqq q = NRPN MSB irefer to table below j
DATA ENTRY MSB 00000110(06H)
DATA VALUE 0mmmmmmm m = Data Value
First transmit an NRPN MSB and NRPN LSB to specify the parameter that is to be
controlled. Then use Data Entry to set the value of the specified parameter.
NRPND. ENTRY
MSB LSB MSB LSB PARAMETER NAME DATA RANGE
01H 08H mmH --- VIBRATO RATE 00H - 40H - 7FH (-64 - 0 - +63)
01H 09H mmH --- VIBRATO DEPTH 00H - 40H - 7FH (-64 - 0 - +63)
01H 0AH mmH --- VIBRATO DELAY 00H - 40H - 7FH (-64 - 0 - +63)
01H 20H mmH --- FILTER CUTOFF FREQUENCY00H - 40H - 7FH (-64 - 0 - +63)
01H 21H mmH --- FILTER RESONANCE 00H - 40H - 7FH (-64 - 0 - +63)
01H 63H mmH --- EG ATTACK TIME 00H - 40H - 7FH (-64 - 0 - +63)
01H 64H mmH --- EG DECAY TIME 00H - 40H - 7FH (-64 - 0 - +63)
01H 66H mmH --- EG RELEASE TIME 00H - 40H - 7FH (-64 - 0 - +63)
14H rrH mmH --- DRUM INST FILTER 00H - 40H - 7FH (-64 - 0 - +63)
CUTOFF FREQ.
15H rrH mmH --- DRUM INST FILTER 00H - 40H - 7FH (-64 - 0 - +63)
RESONANCE
16H rrH mmH --- DRUM INST AEG ATTACK 00H - 40H - 7FH (-64 - 0 - +63)
RATE
17H rrH mmH --- DRUM INST AEG DECAY 00H - 40H - 7FH (-64 - 0 - +63)
18H rrH mmH --- DRUM INST PITCH COARSE 00H - 40H - 7FH (-64 - 0 - +63)
RATE
19H rrH mmH --- DRUM INST PITCH FINE 00H - 40H - 7FH (-64 - 0 - +63)
1AH rrH mmH --- DRUM INST LEVEL 00H - 7FH (0 - maximum)
1CH rrH mmH --- DRUM INST PANPOT 00H ,01H - 40H - 7FH
(random,left - center - right)
1DH rrH mmH --- DRUM INST REVERB SEND 00H - 7FH (0 - maximum)
LEVEL
1EH rrH mmH --- DRUM INST CHORUS SEND 00H - 7FH (0 - maximum)
LEVEL
1FH rrH mmH --- DRUM INST VARIATION 00H - 7FH (0 - maximum)
SEND LEVEL
MSB 14h-1Fh (for drum) are valid only if that channel is set to Drum Set mode
rrH : drum instrument note number
(3-5) SYSTEM REAL TIME MESSAGES
(3-5-1) ACTIVE SENSING
STATUS 11111110 (FEH)
Transmitted at intervals of approximately 200 msec.
Not transmitted during disk read/write operations.
Once this message is received, sensing will begin. If neither status nor data
messages are received for an interval longer than approximately 350 msec, the MIDI
receive buffer will be cleared, and all sounding notes and the Sustain switch will
be forced off. Also, the various controls will be reset to specific values.
(3-6) SYSTEM EXCLUSIVE MESSAGE
(3-6-1)UNIVERSAL NON REALTIME MESSAGE
(3-6-1-1)GENERAL MIDI MODE ON
F0H 7EH 7FH 09H 01H F7H
The following controller values will be reset.
VOLUME 100
PAN Center
PROGRAM CHANGE 1 (Grandpno)
BANK SELECT MSB 0
REVERB DEPTH 4
PITCH BEND CHANGE 0 (center)
MODULATION 0 (off)
EXPRESSION 127 (maximum)
SUSTAIN SWITCH 0 (off)
SOSTENUTO SWITCH 0 (off)
RPN condition of un-specified number
PORTAMENT CONTROL reset
MIDI MASTER VOLUME 127 (maximum)
PITCH BEND SENSITIBITY 02 (2 semitones j
FINE TUNING 0
COURSE TUNING 0
(3-6-1-2)IDENTITY REQUEST (received only)
F0H 7EH 0nH 06H 01H F7H( gn h is the device number, but the QY700 receives this in
Omni)
(3-6-1-3)IDENTITY REPLY (transmitted only)
F0H 7EH 7FH 06H 02H 43H 00H 41H ddH ddH 00H 00H 00H 01H F7H
dd;Device Number Code QY700 = 01H,79H
(3-6-2)UNIVERSAL REALTIME MESSAGE
(3-6-2-1) MIDI MASTER VOLUME
F0H 7FH 7FH 04H 01H llH mmH F7H
Modifies the Master Volume value.
The value of gmm h is used as the MIDI master volume. ( gll h value is ignored)
(3-6-3)PARAMETER CHANGE
(3-6-3-1) MIDI MASTER TUNING
F0H 43H 1nH 27H 30H 00H 00H mmH llH ccH F7H
Modifies the Master Tune value.
The gmm h and gll h values are used as the MIDI master tuning. ( gn h and gcc h
values are ignored)
T = M*200/256-100
Where T: actual tuning value (-99 - +99)
M: a one-byte value with MSB of gmm h bits 0-3, and LSB of gll h bits 0-3.
(3-6-3-2) XG SYSTEM ON
11110000 F0 Exclusive status
01000011 43 YAMAHA ID
0001nnnn 1n device Number
01001100 4C Model ID
0aaaaaaa 00 Address High
0aaaaaaa 00 Address Mid
0aaaaaaa 7E Address Low
00000000 00 Data
11110111 F7 End of Exclusive
When ON is received, the System Mode will be changed to XG.
Since approximately 50 ms is required in order to execute this message, an
appropriate interval must be allowed before the next message.
Controllers will be reset, and all Multi Part and Effect data of the attached table,
together with the values of all data of All System that are noted as (XG), will be
reset to the default values.
(3-6-3-3) XG PARMETER CHANGE
11110000 F0 Exclusive status
01000011 43 YAMAHA ID
0001nnnn 1n device Number
01001100 4C Model ID
0aaaaaaa aaaaaaa Address High
0aaaaaaa aaaaaaa Address Mid
0aaaaaaa aaaaaaa Address Low
0ddddddd ddddddd Data
b b
11110111 F7 End of Exclusive
For parameters with a data size of 2 or 4, the corresponding amount of data will be
transmitted.
For addresses and byte counts, refer to the attached tables.
The following four types are transmitted and received. (Transmitted only if a
Parameter Change Request is received.)
Multi Effect Data iignored in Voice mode j
Multi Part Data iignored in Voice mode j
Drums Setup Data
(3-6-4)BULK DUMP
(3-6-4-1) XG BULK DUMP
11110000 F0 Exclusive status
01000011 43 YAMAHA ID
0000nnnn 0n device Number
01001100 4C Model ID
0bbbbbbb bbbbbbb ByteCount
0bbbbbbb bbbbbbb ByteCount
0aaaaaaa aaaaaaa Address High
0aaaaaaa aaaaaaa Address Mid
0aaaaaaa aaaaaaa Address Low
00000000 00 Data
b b
0ccccccc ccccccc Check-sum
11110111 F7 End of Exclusive
For addresses and byte counts, refer to the attached tables.
Check sum is the value which produces a lower 7 bits of zero when the Byte Count,
Start Address, Data, and the Check-sum itself are added.
513 bytes or more must not be transmitted at once. Thus, if a dump request for 513
or more bytes is received, the data will be divided into packets of 512 bytes or
less, and transmitted at an appropriate timing interval (120 msec or longer).
35
MIDI Data Format