QY100
22
A. HOW TO ENTER THE TEST PROGRAM
While pressing the [AMP SIMULATOR], [PARAMETER] and
[SONG] keys simultaneously, turn on the power to the main
unit. Then the screen of the display unit appears as shown
below.
QY100 TEST
MAIN ROM Ver #.##
SUB CPU Ver #.##
[F1]:AUTO
[F2]:MANUAL
[F3]:Factory Set
[F4]:Exit
Using the [F1], [F2], [F3] or [F4] key, select the mode.
[F1]: The AUTO test mode will be initiated.
[F2]: The MANUAL test mode will be initiated.
[F3]: Test “13. FACTORY RESET” will be executed.
[F4]: Test “19. EXIT” will be executed.
B. HOW TO PROCEED TESTING
1. AUTO mode
When testing in the AUTO mode is initiated, the following
display will appear.
QY100 TEST AUTO
MAIN ROM Ver #.##
SUB CPU Ver #.##
01:RAM R/W
[ENTER]:Test Start
[-1,+1]:INC,DEC
[F4]:Exit
Using the [+1] and [-1] keys, select the test number to be
executed.
Pressing the [ENTER] key will cause the tests of the selected
numbers to be executed as they are selected.
Pressing the [ENTER] key without any setting will cause
the tests to be executed automatically in the order of the
test numbers starting with “1. RAM”.
If an error occurs, it is indicated on the display unit and
testing is stopped. There are three ways to cope with such
an error. Pressing the [ENTER] key will cause testing to be
executed again automatically from the test where the error
occurred. Pressing the [+1] key will cause testing to be
executed again automatically from the test immediately after
the one where the error occurred. Pressing the [F4] key will
cause “19. EXIT” test to be executed.
2.
MANUAL mode
When testing in the MANUAL mode is initiated, the screen
of the display unit appears as shown below.
QY100 TEST
MANUAL
MAIN ROM Ver #.##
SUB CPU Ver #.##
01:RAM R/W
[ENTER]:Test Start
[-1,+1]:INC,DEC
[F4]:Exit
Using the [+1] and [-1] keys, select the test number to be
executed.
Pressing the [ENTER] key will cause the test of the selected
number to be executed.
Pressing the [F4] key will cause “19. EXIT” test to be
executed.
C. HOW TO PROCEED TESTING WHEN JUDGED AS NG
If testing is judged as NG, it is possible to select whether to
repeat the same test again or to move on to the next test
item by using the following procedure.
AUTO mode: Pressing the [F4] key will set to the error
processing state.
MANUAL mode: Pressing the [F4] key will set to the test
number waite state. However, this method cannot be used
when testing the [F4] key in “6. PANEL SWITCH” test.
Described below are how each test is executed mainly in
the MANUAL mode.
1. SYSTEM RAM TEST
Initial Display
QY100 TEST
MANUAL
MAIN ROM Ver=#.##
SUB CPU Ver=#.##
01:RAM R/W
[ENTER]:Test Start
[-1,+1]:INC,DEC
[F4]:Exit
Test Procedure
Press the [ENTER] key, and a read/write test of MAIN CPU
and SUB CPU RAM will be executed automatically.
Содержание QY100 Data Filer
